Thermal Dynamics CUTMASTER Service Manual

CUTMASTER 40mm
Manual 0-5085 1-1 GENERAL INFORMATION
SECTION 1:
GENERAL INFORMATION
1.01 Notes, Cautions and Warnings
Throughout this manual, notes, cautions, and warnings are used to
highlight important information. These highlights are categorized as
follows:
NOTE
An operation, procedure, or background informa-
tion which requires additional emphasis or is help-
ful in efficient operation of the system.
CAUTION
A procedure which, if not properly followed, may
cause damage to the equipment.
!
WARNING
A procedure which, if not properly followed, may
cause injury to the operator or others in the op-
erating area.
WARNING
Gives information regarding possible electrical
shock injury. Warnings will be enclosed in a box
such as this.
1.02 Important Safety Precautions
!
WARNING
OPERATION AND MAINTENANCE OF PLASMA ARC
EQUIPMENT CAN BE DANGEROUS AND HAZARD-
OUS TO YOUR HEALTH.
Plasma arc cutting produces intense electric and
magnetic emissions that may interfere with the
proper function of cardiac pacemakers, hearing
aids, or other electronic health equipment. Persons
who work near plasma arc cutting applications
should consult their medical health professional
and the manufacturer of the health equipment to
determine whether a hazard exists.
To prevent possible injury, read, understand
and follow all warnings, safety precautions and
instructions before using the equipment. Call
1-603-298-5711 or your local distributor if you
have any questions.
GASES AND FUMES
Gases and fumes produced during the plasma cutting process can be
dangerous and hazardous to your health.
• Keepallfumesandgasesfromthebreathingarea.Keepyour
head out of the welding fume plume.
• Useanair-suppliedrespiratorifventilationisnotadequateto
remove all fumes and gases.
• Thekindsoffumesandgasesfromtheplasmaarcdependon
the kind of metal being used, coatings on the metal, and the
different processes. You must be very careful when cutting
or welding any metals which may contain one or more of the
following:
Antimony Chromium Mercury
Arsenic Cobalt Nickel
Barium Copper Selenium
Beryllium Lead Silver
Cadmium Manganese Vanadium
• AlwaysreadtheMaterialSafetyDataSheets(MSDS)thatshould
be supplied with the material you are using. These MSDSs
will give you the information regarding the kind and amount of
fumes and gases that may be dangerous to your health.
• Forinformationonhowtotestforfumesandgasesinyour
workplace, refer to item 1 in Subsection 1.03, Publications in
this manual.
• Usespecialequipment,suchaswaterordowndraftcutting
tables, to capture fumes and gases.
• Donotusetheplasmatorchinanareawherecombustibleor
explosive gases or materials are located.
• Phosgene,atoxicgas,isgeneratedfromthevaporsofchlo-
rinated solvents and cleansers. Remove all sources of these
vapors.
• Thisproduct,when usedforweldingorcutting,produces
fumes or gases which contain chemicals known to the State
of California to cause birth defects and, in some cases, cancer.
(CaliforniaHealth&SafetyCodeSec.25249.5etseq.)
ELECTRIC SHOCK
Electric Shock can injure or kill. The plasma arc process uses and
produces high voltage electrical energy. This electric energy can cause
severe or fatal shock to the operator or others in the workplace.
• Nevertouchanypartsthatareelectrically“live”or“hot.”
• Weardryglovesandclothing.Insulateyourselffromthework
piece or other parts of the welding circuit.
• Repairorreplaceallwornordamagedparts.
• Extracaremustbetakenwhentheworkplaceismoistordamp.
• InstallandmaintainequipmentaccordingtoNECcode,refer
toitem9inSubsection1.03,Publications.
• Disconnectpowersourcebeforeperforminganyserviceor
repairs.
• ReadandfollowalltheinstructionsintheOperatingManual.
FIRE AND EXPLOSION
Fireandexplosioncanbecausedbyhotslag,sparks,ortheplasmaarc.

Thermal Dynamics CUTMASTER Specifications

General

Brand	Thermal Dynamics
Model	CUTMASTER
Category	Welding System
Language	English