Watlow F4P Series

Watlow Series F4P Appendix ■ A.11
P, Q
pages, software A.13 – A.14
parameter records
Custom Main Page 6.25
Operations Page 6.10
Setup Page 6.23 – 6.24
parameter setup order 4.1
Parameter x (1 to 16) 6.2, 6.21
password lock 5.1
password, setting or changing 5.2
PI control 7.7
droop 7.7
Integral 7.7
overshoot 7.7
reset 7.7
PID 7.7
PID block — see PID Set
PID control 7.7
derivative 7.7
autotuning 7.9
PID Cross 6.7
PID Crossover 6.7
PID parameters, adjusting manually
3.2
PID Set x (1 to 5), Cascade PID 3.3 –
3.4, 6.5 – 6.6, 7.16
PID Set x (1 to 5), PID Set Channel 1
6.4 – 6.5
PID Units 4.1, 6.11
PID, multiple sets 7.8
power level 7.12
power wiring 8.5
Process 6.18
process alarm 7.10
Process Display 6.22
Process Display Menu 6.22
process input, wiring 8.6, 8.8
process or deviation alarms 3.1, 7.10
Process Output Calibration 5.5
process tracking 7.5
Propband — see Proportional Band
proportional action 7.6 – 7.7
Proportional Band x (A or B), Cascade
PID 3.3 – 3.4, 6.5, 7.16
Proportional Band x (A or B), PID Set
Channel 1 3.2, 6.4, 7.6 – 7.7
proportional control 7.6 – 7.7
proportional integral derivative (PID)
control 7.7
proportional plus integral (PI) control
7.7
proportional plus integral plus deriva-
tive (PID) control 7.7
PV bias — see multiple input offsets
R
Ramp to Set Point Menu 6.7
Ramp to Set Point Mode 6.7
Ramp to Set Point Rate 6.8
Ramp to Set Point Scale 6.8
rate alarm 3.1, 7.10
Rate x (A or B), Cascade PID 3.3 – 3.4,
6.6, 7.16
Rate x (A or B), PID Set Channel 1 3.2,
6.5
Ratio Control 7.17
Ratio set point 6.2
read only (security level) 5.1
Records
Custom Main Page 6.25
Operations Page 6.10
Setup Page 6.23 – 6.24
reference compensator 5.3
Remote/Local Set Point 6.9
Remote Set Point 7.15
removing the controller 8.4
reset 7.7
reset value 7.7
Reset x (A or B) 3.2
Reset x (A or B), Cascade PID 3.3 –
3.4, 6.6, 7.16
Reset x (A or B), PID Set Channel 1
6.5
resistance temperature detector — see
RTD
Restore Input x (1 to 3) Calibration
6.31
restoring factory calibration values 5.3
retransmit 7.9
Retransmit Output x (1 and 2) Menu
6.20, 7.4
Retransmit Outputs
calibration 5.6
wiring 8.11
Retransmit Source 6.20
Retransmit x (1 or 2) 6.28
Reverse outputs 6.17
Revision 6.27
RFI 7.8
Right Key 2.2
rising edge 7.4
RTD
input calibration 5.3 – 5.4
inputs, wiring 8.6 – 8.7
S
safety info inside front cover
Scale High 6.13, 7.4
Scale Low 6.13, 7.4
Scale Offset 6.20
Scaling 6.14, 7.4
scroll bar 2.2
security and locks, overview 5.1
passwords 5.2
security levels 5.1
Set Lockout Menu 6.26 – 6.27
security levels 5.1
self tune — see autotune
self-clearing alarm 7.11
Sensor 6.12
sensor installation guidelines 8.5
accuracy ranges A.2
process input 8.6, 8.8
RTD input 8.6 – 8.7
thermocouple inputs 8.6 – 8.7
Serial Number 6.27
Set Lockout Menu 6.26 – 6.27
Set Point High Limit 6.13
Set Point Low Limit 6.13
Set Point, Set Lockout 6.26
set point
locking out 5.1
manual tuning 3.2
ramping to 6.7 – 6.8
remote 6.9, 7.15
static control 2.3
Set Point 6.26
Set Point High Limit 6.13, 7.3
Set Point Low Limit 6.13, 7.3
set variable — see set point
Set/Change Password 6.26
setup
customizing the Main Page 4.2
guided 2.3
guidelines 4.1
overview 4.1
parameter record 6.23 – 6.24