YASKAWA FSDrive-MV1000 Series - Options; Built-In Type

7.2 Options
YASKAWA ELECTRIC TOEP C710687 02B FSDrive-MV1000 Instructions 213
Options
7
7.2 Options
Table 7.1 lists the names of the various options available for the drive. Contact your Yaskawa representatives or the
nearest Yaskawa sales office.
• Option Selection: Refer to the Yaskawa catalog for selection and part numbers.
• Option Installation: Refer to the corresponding option manual for installation and wiring instructions.
u Built-in Type
All built-in type options mount to the connectors on the controller board.
Table 7.1 Built-in Type Options
Type Name Function Reference Manual
Speed (Frequency)
Reference Card
<1> Only one communication card can be selected at a time.
<2> To apply PG control, the PG speed control card must be selected.
<3> Contact Yaskawa for documentation.
Analog Input
AI-A3
Enables high-precision and high-resolution analog speed reference
setting.
• Input signal level: -10 to +10 Vdc (20 kΩ), 4 to 20 mA (500 Ω)
• Input channels: 3 channels (DIP switch for input voltage/input
current selection)
• Input resolution: Input voltage 13-bit signed (1/8192)
Input current 1/6554
This manual or
FSDrive-MV1000
Parameter Guide
(TOEP C710687 03)
Digital Input
DI-A3
Enables 16-bit digital speed reference setting.
• Input signal: 16 bit binary, 4-digit BCD + sign signal + set signal
• Input voltage: +24 V (isolated)
• Input current: 8 mA
User-set: 8-bit, 12-bit, 16-bit
This manual or
FSDrive-MV1000
Parameter Guide
(TOEP C710687 03)
Communications
Card
<1>
DeviceNet Interface
SI-N3
Connects to a DeviceNet network. Using this communications
protocol, it is possible to run and stop the drive, set and reference
parameters, and monitor output frequency, output current, or similar
items.
FSDrive-MV1000 Option
DeviceNet Technical
Manual
(SIEP C710687 04)
PROFIBUS-DP
Interface
SI-P3
Connects to a PROFIBUS-DP network. Using this communications
protocol, it is possible to run and stop the drive, set and reference
parameters, and monitor output frequency, output current, or similar
items.
FSDrive-MV1000 Option
PROFIBUS-DP Technical
Manual
(SIEP C710687 05)
Monitor Card
Analog Monitor
AO-A3
Outputs analog signal for monitoring drive output state (output freq.,
output current etc.).
• Output resolution: 11-bit signed (1/2048)
• Output voltage: -10 to +10 Vdc (non-isolated)
• Terminals: 2 analog outputs
This manual or
FSDrive-MV1000
Parameter Guide
(TOEP C710687 03)
Digital Output
DO-A3
Outputs isolated type digital signal for monitoring drive run state
(alarm signal, zero speed detection, etc.)
• Terminals: 6 photocoupler outputs (48 V, 50 mA or less)
2 relay contact outputs (250 Vac 1 A or less, 30 Vdc 1 A
or less)
This manual or
FSDrive-MV1000
Parameter Guide
(TOEP C710687 03)
PG Speed
Controller Card
<2>
Complementary Type
PG Interface
PG-B3
For control modes requiring a PG encoder for motor feedback.
• Phase -A, -B, and -Z pulse (3-phase) inputs (complementary type)
• Max. input frequency: 50 kHz
• Pulse monitor output: Open collector, +24 V, max. current 30 mA
• Power supply output for PG: +12 V, max. current 200 mA
This manual or
FSDrive-MV1000
Parameter Guide
(TOEP C710687 03)
Line Driver PG
Interface
PG-X3
For control modes requiring a PG encoder for motor feedback.
• Phase -A, -B, and -Z pulse (differential pulse) inputs (RS-422)
• Max. input frequency: 300 kHz
• Pulse monitor output: RS-422
• Power supply output for PG: +5 V or +12 V, max. current 200 mA
This manual or
FSDrive-MV1000
Parameter Guide
(TOEP C710687 03)
PLC Function
Expansion PLC Board
BC-620
Supplements PLC functions required to customize the drive.
• Program memory capacity: Equivalent to 8,000 steps
• Execution speed: 1,000 steps/1 ms
• Language: Ladder language, textual language
<3>