YASKAWA GA800 Series - Page 110

3.9 Braking Resistor Installation
110 YASKAWA SIEPC71061737B GA800 Drive Technical Reference
Table 3.17 200 V Class
Drive Model
Braking Unit
(Quantity)
Drive Terminals
Recommended Gauge
(AWG, kcmil)
Applicable Gauge
(AWG, kcmil)
Reference
2257
CDBR-2022D
(× 2)
Specified Wire Gauge
+3 10 × 2P 10 - 8 × 2P Figure 3.59
- 10× 2P 10 - 8 × 2P Figure 3.59
Applicable Gauge
*1
+3 1/0 × 2P 4 - 1/0 × 2P Figure 3.60
- 1/0 × 2P
*2
4 - 1/0 × 2P
*2
Figure 3.60
2313
CDBR-2110D
(× 1)
Specified Wire Gauge
+3 3 3 - 2 Figure 3.59
- 3 3 - 2 Figure 3.59
Applicable Gauge
*1
+3 1/0 × 2P 4 - 1/0 × 2P Figure 3.60
- 1/0 × 2P
*2
4 - 1/0 × 2P
*2
Figure 3.60
2360
CDBR-2110D
(× 1)
Specified Wire Gauge
+3 3 3 - 2 Figure 3.61
- 3 3 - 2 Figure 3.61
2415
CDBR-2110D
(× 1)
Specified Wire Gauge
+3 3 3 - 2 Figure 3.61
- 3 3 - 2 Figure 3.61
*1 This is the applicable wire gauge when you use a braking unit other than Yaskawa braking unit (CDBR-type).
*2 This is the applicable wire gauge when you use the same wires for terminal - and terminal +3.
Table 3.18 400 V Class
Drive Model
Braking Unit
(Quantity)
Drive Terminals
Recommended Gauge
(AWG, kcmil)
Applicable Gauge
(AWG, kcmil)
Reference
4208
CDBR-4045D
(× 2)
Specified Wire Gauge
+3 10 × 2P 10 - 8 × 2P Figure 3.59
- 10 × 2P 10 - 8 × 2P Figure 3.59
Applicable Gauge
*1
+3 1/0 × 2P 4 - 1/0 × 2P Figure 3.60
- 1/0 × 2P
*2
4 - 1/0 × 2P
*2
Figure 3.60
4250
CDBR-4220D
(× 1)
Specified Wire Gauge
+3 3 3 - 2 Figure 3.59
- 3 3 - 2 Figure 3.59
Applicable Gauge
*1
+3 1/0 × 2P 4 - 1/0 × 2P Figure 3.60
- 1/0 × 2P
*2
4 - 1/0 × 2P
*2
Figure 3.60
4302
CDBR-4220D
(× 1)
Specified Wire Gauge
+3 3 3 - 2 Figure 3.59
- 3 3 - 2 Figure 3.59
Applicable Gauge
*1
+3 1/0 × 2P 4 - 1/0 × 2P Figure 3.60
- 1/0 × 2P
*2
4 - 1/0 × 2P
*2
Figure 3.60
4371
CDBR-4220D
(× 1)
Specified Wire Gauge
+3 3 3 - 2 Figure 3.61
- 3 3 - 2 Figure 3.61
4414
CDBR-4220D
(× 1)
Specified Wire Gauge
+3 3 3 - 2 Figure 3.61
- 3 3 - 2 Figure 3.61
4477
CDBR-4220D
(× 1)
Specified Wire Gauge
+3 3 3 - 2 Figure 3.62
- 3 3 - 2 Figure 3.62
Applicable Gauge
*1
+3 3/0 × 4P 2 - 4/0 × 4P Figure 3.64
- 3/0 × 4P
*2
2 - 4/0 × 4P
*2
Figure 3.64