2gig Technologies GC2 User Manual

Copyright © 2016 Nortek Security & Control 29
REMOTE CONTROL BY TELEPHONE
Youcancontrolyoursystemremotelyusing
astandardtelephone(r equirestheoptional
POTSmoduleavailableonlyintheUnited
StatesandCanada).Remotecontrolis
performe dbycallingthesystemand
respondingtospokenquestionsfromthe
system.Bypressingcertaintelephonekeys,
youcandothefollowing:
•Armthesystem
•Disarmthesy
stem
•Bypassse
nsors
•Querysy
stemstatus
NOTE: Attheti
meyoursystemwas
installed,yourinstallerneededto
enabletheoptionalremote
controlbytelephonefeature.
Otherwiseyouwillbeunableto
usetheremotecontrolby
telephonefeature.
CALLING THE SYSTEM
Duringinstallation,yourinstallerselects
whetheryoursystemsupportstheremote
telephoneoptionornot.Ifthisfeatureis
enabled,thesystemrequiresyoutocall
twicewithin30secondsbeforeitanswers
yourcall.
1 Callthetelephonenumberthatthe
ControlPanelisconnectedto.Waitfor
oneortworings,thenhangup.
2 Within10‐45seconds,calltheControl
Panelagain.TheControlPanelanswers
thecall.
CONTROLLING THE SYSTEM
REMOTELY
Talktoyourdealertoseeifyoursystemwas
installedwiththePOTSmodule.Onceyou
areconnectedwiththesystemviathe
telephone,youcancheckonsystemstatus
andremotelycontrolthemajorfunctions.
TIP: Theannouncementsthatthesystem
playsoverthetelephonedonotsound
outoftheCon
trolPanel’ sspeaker.
1 AftertheControlPanelanswers,itsasks
foryourusercode.Youhave15seconds
toenteryourusercodeusingthe
telephonekeys.Ifyoudon’tentera
validusercodein15seconds,the
systemdisconnectsthecall.
If2attemptsusing2telephonecallsto
enterausercodewithinafive(5)
minutetimeframefailtoenteravalid
code,thesystemdisconnectsanddoes
notrespondtotelephonecommandsfor
30minutes.
2 Afterthesystemhasacceptedyouruser
code,itannouncesthesystemstatus,
thentheremotecommandoptions.
Thesy
stemwaitsupto60secondsfor
eachremotecommandbefor e
automaticallydisconnecting.Ifyou
knowtheremotecommandnumber,
youcanenteritatanytime.Usethe
followingtelephonekeystocontrolyour
system.:
Press1 ForSystemStatusReport
Press2
ToArmtheSysteminAwaymode
Press3 ToArmtheSysteminStaymode
Press4
ToDisarmthesystem
Press5 ToturnONAuxiliaryOutput(ifused)
Press6
ToturnOFFAuxiliary Output(ifused)
Press7 TostopSystemStatusReport
Press8
ToHangUp
Press9 ToRepeattheCommandMenu
Press# ToBy
passAllOpenSensorsandArmthe
System
NOTE: Remembertotap8tohangup
whenyouarefinishedremotely
controllingthesystem.
TIP: Ther
eisnoExitDelaywhenyou
remotelyarmthesystem.
TIP: TheAutoStayfeature(ifenabled)does
notfunctionwhenyouremotelyarmthe
system.
BYPASSING SENSORS
REMOTELY
Ifthereareopensensorswhenyoutryto
armthesystemremotely,thesystem
announcesthecurrentstatusandasks:“To
bypasssensorsandarm,presspound.”
1 Tobypassallopensensorsandarmthe
system,press#.
Aftertheopense
nsorsarebypassed,the
systemarmsinthemodeyouselectedand
announcesthesystemstatustoyou.

2gig Technologies GC2 Specifications

General

Brand	2gig Technologies
Model	GC2
Category	Security System
Language	English