Index
Index-9
scale and offset, 7-8
smoothing
, 7-8
sweep-to-sweep averaging
, 7-6
trace math operation
, 7-7
transform
, 7-8
vector error-correction
, 7-7
processing, data
, 7-5
prompting user to connect mixer
test setup
, 2-29
purging a sequence from a disk
,
1-104
R
R channel inputs, internal and
external
, 2-10
range
, 3-30
forward transform
, 3-24
resolution
, 3-34
ratio calculations
, 7-6
ratio measurements in channel 1
and 2, to
, 1-20
raw arrays
, 7-7
raw source match
, 7-71
real format
, 7-29
recall time, reducing
, 5-18
recalling a file
, 4-54
solving problems
, 4-55
recalling instrument states
, 4-36
receiver
calibration
, 6-15
crosstalk, reducing
, 5-15, 5-18
noise floor, reducing
, 5-15
receiver block
, 7-4
reducing
averaging factor
, 5-12
effect of spurious responses
, 2-5
number of measurement points
,
5-12
reducing recall time
, 5-18
reducing trace noise
, 5-16
activating averaging
, 5-16
changing system bandwidth
,
5-16
reduction, IF bandwidth
, 7-35
reference plane and port
extensions
, 5-5
reflection measurements
response and isolation error
correction
, 6-19
response error correction
, 6-12
reflection measurements in time
domain low pass
, 3-16
interpreting the low pass
response horizontal axis
,
3-16
interpreting the low pass
response vertical axis
, 3-16
reflection measurements using
bandpass
interpreting the band pass
reflection response vertical
axis
, 3-13
reflection measurements using
bandpass mode
, 3-12
interpreting the bandpass
reflection response
horizontal axis
, 3-13
reflection response
measurements, making
, 3-9
relative velocity factor, adjusting
,
3-12
removing adapter delay
, 6-42
removing the effect of an adapter
,
6-74
renaming a file
, 4-53
repeatability, connector
, 5-4
repetitive switching of the
attenuator
, 7-13
required peripheral equipment
,
7-4
required test equipment,
connecting
, 1-4
requirements for TRL standards
,
7-72
re-saving an instrument state
,
4-51
resetting
plotting parameters to default
values
, 4-18
printing parameters to default
values
, 4-7
resolution
, 3-32
range resolution
, 3-34
response resolution
, 3-32
response
calibration
, 2-29
error correction for reflection
measurements
, 6-12
error correction for transmission
measurements
, 6-14
magnitude
, 1-7
resolution
, 3-32
response and isolation
calibration
, 7-54
response and isolation error
correction for reflection
measurements
, 6-19
response calibration
, 7-54
restarting a calibration
, 6-5
reverse isolation
, 1-57
reviewing the limit line segments
,
1-79
RF feedthrough
, 2-47
RF frequency range
, 2-22
using the calculation
, 2-22
using the mixer measurement
diagram
, 2-17, 2-23
RF range
power meter calibration
, 2-23
RF, defining
, 2-7
ripple limit testing
, 1-81–1-91
ripple limits
editing
, 1-84–1-86
running the test
, 1-86–1-91
setting
, 1-81–1-84
ripple test
absolute value
, 1-89
displaying limits
, 1-87
displaying values
, 1-88
frequency bands
, 1-83
margin value
, 1-91
message color
, 1-87
starting and stopping
, 1-86
running a bandwidth test
,
1-94–1-97
running a limit test
, 1-79
running a sequence
, 1-100
running the ripple limits test
,
1-86–1-91
S
S11 and S22 one-port calibration
,
7-55
S2P data format
, 4-42
safety considerations
, 8-5
before applying power
, 8-5
compliance with German FTZ
emissions requirements
, 8-8
compliance with German noise
requirements
, 8-8
general
, 8-7
safety earth ground
, 8-5
servicing
, 8-6
safety earth ground
, 8-5
safety symbols
, 8-4
sample-and-sweep correction
mode, using
, 6-36
sampler/IF correction
, 7-6
saving
calibration data
, 6-5, 7-65
data trace
, 1-19
instrument state
, 4-38, 7-65
measurement results
, 4-39
measurement results
graphically
, 4-46
modified calibration kits
, 7-65
to a disk
, 7-65
saving a file
solving problems
, 4-55
saving and recalling instrument
states
, 4-36
To Next Page
Loading...
Need help?
General
