Index-10
Index
places where you can save, 4-36
what you can save to a
computer
, 4-37
what you can save to a floppy
disk
, 4-37
what you can save to the
analyzer’s internal memory
,
4-36
saving measurement results
ASCII data formats
, 4-41
instrument state files
, 4-47
scale and offset
, 7-8
scale, choosing
, 4-17
searching for specific amplitude
,
1-39
segment menu
, 7-16
segment power, setting
, 7-18
selecting
auto-feed
, 4-15
gate shape
, 3-36
line types
, 4-17
pen numbers and colors
, 4-16
selecting sweep modes
, 7-19
sending the exit HPGL mode and
form feed sequence to the
printer
, 4-26
sending the HPGL initialization
sequence to the printer
, 4-26
sending the plot file to the printer
,
4-26
sequence
changing the title
, 1-103
clearing from memory
, 1-102
creating
, 1-98
decision making menu
, 1-112
editing
, 1-100
generating files in a loop counter
example
, 1-116
in-depth information
, 1-105
jumps to itself
, 1-112
limit test example
, 1-118
loading from a disk
, 1-104
loop counter example
, 1-115
naming files
, 1-103
printing
, 1-105
purging from a disk
, 1-104
running
, 1-100
size
, 1-106
stopping
, 1-100
storing to disk
, 1-104
sequencing
special functions menu
, 1-112
test
, 1-98
service menu (ECal)
, 6-67
servicing
, 8-6
setting
auto sweep time mode
, 5-12
frequency range for time domain
low pass
, 3-15
gate
, 3-35
setting ripple limits
, 1-81–1-84
setting segment IF bandwidth
,
7-19
setting segment power
, 7-18
setting the sweep type
, 5-12
setting up bandwidth test limits
,
1-92–1-94
shipment for service
, 8-2
sidelobes
, 3-27
single page plots, outputting
using a printer
, 4-26
single point limits
, 1-77
sloping limit line
, 1-75
small signal transient response,
measuring
, 3-19
smith chart format
, 7-26
smith chart markers
, 1-33
smoothing
, 7-8, 7-35
softkey
4 Param Displays
, 1-18
channel position
, 1-17
solving problems with printing or
plotting
, 4-35
solving problems with saving or
recalling files
, 4-55
using an external disk drive
,
4-55
source attenuator switch
protection
, 7-13
repetitive switching of the
attenuator
, 7-13
source match
, 7-39
source match and load match
,
7-70
source mismatches, minimizing
,
2-4
source power, setting
, 1-5
source step attenuator
, 7-4
S-parameter menu
analog in menu
, 7-22
conversion menu
, 7-22
S-parameters
, 7-20
S-parameter menu
, 7-22
understanding
, 7-20
S-parameters menu
input ports menu
, 7-23
specific amplitude
, 1-39
bandwidth, searching for
, 1-41
maximum amplitude, searching
for
, 1-39
minimum amplitude, searching
for
, 1-39
target amplitude, searching for
,
1-40
tracking the amplitude
, 1-41
spreadsheet, saving test file for a
,
4-44
spurious responses, reducing the
effect of
, 2-5
standards, calibration
, 6-5
start frequency, setting
, 1-34
starting the ripple test
, 1-86
statistics of measurement data,
calculating
, 1-42
stepped edit list menu
, 7-16
stepped edit subsweep menu
, 7-16
stepped list frequency sweep
, 7-15
segment menu
, 7-16
stepped edit list menu
, 7-16
stepped edit subsweep menu
,
7-16
stepped list mode
, 1-67
stimulus state, error-correction
,
6-9
stop frequencies, minimum
allowable
, 3-16
stop frequency, setting
, 1-35
stopping a sequence
, 1-100
stopping the ripple test
, 1-86
storing
exit HPGL mode and form feed
sequence
, 4-26
HPGL initialization sequence
,
4-25
sequence on a disk
, 1-104
sweep
rate, decreasing
, 5-9
retrace
, 5-7
speed, increasing
, 5-10
type, setting
, 5-12
sweep time
, 7-11
auto sweep time mode
, 7-11
manual sweep time mode
, 7-11
minimum sweep time
, 7-11
sweep types
, 7-15
CW time sweep
, 7-19
linear frequency sweep
, 7-15
logarithmic frequency sweep
,
7-15
power sweep
, 7-19
selecting sweep modes
, 7-19
stepped list frequency sweep
,
7-15
swept list frequency sweep
, 7-17
sweep-to-sweep averaging
, 7-6
swept edit list menu
, 7-17
swept edit subsweep menu
, 7-17
swept list frequency sweep
, 7-17
setting segment IF bandwidth
,
7-19
setting segment power
, 7-18
To Next Page
Loading...
Need help?
General
