ATI Series D12 Toxic Gas Transmitter with H10 Smart Sensor
Revision N (7/15) 4
Restart ............................................................................ 72
Resets ............................................................................. 72
SPARE PARTS _______________________ 73
APPENDIX A. ________________________ 76
PRINTING DATA LOG REPORTS ......................................76
Serial Connection ............................................................ 76
Communication Setup Page ............................................ 76
Flow Control .................................................................... 76
Report Format ................................................................. 77
Report Control ................................................................. 77
EXAMPLE: CHARTING A DATA LOG REPORT .................. 78
Starting the Report .......................................................... 81
Charting with Microsoft Excel .......................................... 84
List of Figures
Figure 1. Transmitter, sensor, generator 5
Figure 2. Overall dimensions 9
Figure 3. Duct-mount sensor holder 10
Figure 4 Duct Mount Sensor Exploded View 10
Figure 5. Duct-mount adapter 11
Figure 6. Duct-mount assembly 11
Figure 7. Separating the board stack 12
Figure 8. Power Supply Board Connections 13
Figure 9. ATI A17/B14 Monitors, 2-wire 14
Figure 10. ATI A17/B14 Monitor(s), 3-Wire Mode 15
Figure 11. Power Only, No Output Options 16
Figure 12. Current Loop, Single Supply (2-Wire Mode) 17
Figure 13. Current Loop Single Supply (3-Wire Mode) 18
Figure 14. Current Loop, Dual Supplies (4-Wire Mode) 19
Figure 15. HART Operation, Point-to-Point (2-Wire) 20
Figure 16. HART Operation, Point-to-Point (3-Wire) 21
Figure 17. HART Transmitter Operation, Multi-drop 22
Figure 18. Modbus RS485 multi-drop connections 23
Figure 19. Computer RS232 24
Figure 20 - Remote H10 Sensor Wiring 25
Figure 21 - Duct Mount Wiring 26
Figure 22 - Optional Heated Sensor Wiring 27
Figure 23. CPU Board configuration 28
Figure 24. Operator interface panel 29
Figure 25. Startup review sequence 30
Figure 26. Main display 31
Figure 27. Standard fault indication 31
Figure 28. Variable editing 33
Figure 29. Sensor setup page 34
Figure 30. Data-log warning page 34
Figure 31. Sensor “more” page 35
Figure 32. Sensor removal 35
Figure 33. Generator removal 36
Figure 34. Zero calibration 39
Figure 35. Zero_Sensor page 39
Figure 36 Span calibration 40
Figure 37. Span_Sensor page 40
Figure 38. Calibration of duct-mount H10 sensors (ATI-0664) 41
Figure 39. Sensor calibration history page 42
Figure 40. Auto-test control page 45
Figure 41. Auto-test setup page 45
Figure 42. Auto-test sequence 48
Figure 43. Default alarm relationships for toxic gas sensors. 49
Figure 44. Default alarm relationships for oxygen sensors 49
Figure 45. Manual alarm reset 49
Figure 46. Rising alarm (Active=ABOVE_SP, Reset=AUTO) 50
Figure 47. Falling alarm (Active=BELOW_SP, Reset=AUTO) 50
Figure 48. Alarm setup pages 51
Figure 49. Fault alarm (Main Display) 53
Figure 50. Fault page 53
Figure 51 Alarm relay schematic(default – no alarms active) 56
Figure 52. Relay setup page (example) 57
Figure 53. Relay test page example 57
Figure 54. Inhibiting alarms from the Main Display 58
Figure 55. Alarm inhibit setup page 58
Figure 56. Current loop output plot 59
Figure 57. 4-20mA setup page 59
Figure 58. 4-20mA control page 60
Figure 59. Loop adjustment pages 60
Figure 60. Data log access page 61
Figure 61. Data log setup page 61
Figure 62. Data log graphic report page 62
Figure 63. Data log tabular report page 62
Figure 64. Data-log printout (example) 63
Figure 65. System access page 65
Figure 66. Clock setup page 65
Figure 67. Security control page 66
Figure 68. Activating security 66
Figure 69. Deactivating security 67
Figure 70. Changing the password 67
Figure 71. Communication setup page 68
Figure 72. Hart setup pages 69
Figure 73. Hart a) Find-me and b) Device found pages 70
Figure 74. Modbus setup page 71
Figure 75. Transmitter version page 71
To Next Page
Loading...
