ATI Technologies F12/D

To Next Page

To Previous Page

ATI Model F12/D Gas Transmitter Part 4 – Operation

O&M Manual (Rev-H)

For oxygen sensors, Alarm is a low-low alarm

set to 16%, Warning is a low alarm set to

19.5%, and Caution is a high alarm set to 23%.

Figure 63 depicts the relationships of these

alarms.

Figure 63. Oxygen Deficiency Alarms

Low-Low Alarm

Low Alarm

High Alarm

Main Page

Table of Contents2
Safety5
Warnings5
Hazardous Location Installation5
Part1 - Introduction6
General6
Figure 1- Transmitter W /Sensor6
H10 Smart Sensors7
Specifications9
Part 2 - Mechanical Installation10
Transmitter Mounting10
Enclosure Dimensions10
Figure 2. Enclosure Dimensions10
Wall and Pipe Mounting11
Figure 3 Deep Enclosure Dimensions11
Figure 4 Wall/Pipe Mounting Bracket11
Figure 5. Wall Mounting Diagram12
Figure 6. Pipe Mounting Diagram12
Panel Mounting13
Duct Sensor Mounting13
Sensors Only )13
Figure 7. Panel Mounting Details13
Figure 9. Duct-Mount Assembly14
Duct Mount (Integral)15
Generator Installation /R15
Emoval15
Figure 10 - Duct Mount15
Figure 11 - Generator Explodedv15
Part 3 - Electrical Connections16
Transmitter Connections16
Terminal Board - Sensor17
Onnections17
Figure 13. Sensor /Generatort17
Terminal Board - Loopp18
Figure 14. Power and Communication Terminals18
Heated Sensor Housingw19
Iring19
Figure 15 - Heated Sensor Wiring19
Remote Sensor Wiring20
Figure 16 -Remote Sensor Wiring20
Heated Sensor Wiring21
Figure 17 -Remote Sensor Wiring21
Heated Remote Sensorw22
Iring (2-Wire )22
Figure 18 - Heated Remotes22
Duct Mount Sensorw23
Sensor Connections with23
Iring23
T Cable23
Figure 19 - Duct Mount Sensor23
Figure 20 - Wiring Connections23
Ac or24
Figure 21 - Powered Alarm Relay24
3.11 Relay Configuration25
3.12 Remote Reset Input25
Figure 22 - Relay Configuration25
Figure 23 - Remote Reset Input25
3.14 Wiring Examples26
Ac or27
Figure 25 - Ac or27
Figure 53. S27
Figure 63. T27
Figure 64. O27
Figure 66. L27
Hart Point - to -Point29
Ire )29
Communications Jumper30
Part 4 - Operation31
4.1 Operator Interface Panel31
Menus and Settings31
Moving the Cursor and Selecting31
Editing Settings31
4.2 Startup32
Transmitter Review32
Figure 62. a32
Figure 65. H32
Sensor Review33
Generator Review34
Main Display35
Main Reading35
Trouble Indication36
Timed Return to Main Display36
Inhibiting Alarms from the Main Display36
Displays36
Sensor Removed Display36
Sensor Installed36
Figure 36. Main Display36
Generator Removed37
Generator Installed37
Enu38
4.5 Main Menu38
Alarm Active Menu38
Menus , Methods , and Settings39
Sensor Menu39
Sensor Settings Menu39
Sensor Model Menu39
Sensor Range Menu40
Sensor Calibration41
Sensor Calibration Menu42
Figure 48. S42
Figure 50. S43
Figure 51 S43
Figure 52. S44
Sensor Auto-Test45
Figure 54. a46
Figure 55. a46
Figure 56. a46
Figure 57. a47
Figure 59. G48
Figure 60. a48
Figure 85. G48
Figure 89. a48
Enus , Methods , and Settings49
Alarms Menu49
Gas Level Alarms49
Figure 61. a49
Figure 67. a52
Figure 68. a52
Figure 73. a53
Figure 74. a53
Trouble Alarm54
Alarm Inhibit58
Alarm Test Menu59
Menus , Methods , and Settings60
Data Log Menu60
Data Log Setup Menu61
Data Log View Menu61
Figure 76. D61
Figure 77. D62
Figure 78. D62
Data Log Print Menus, Methods, and Settings63
Figure 79. D63
Figure 80. D63
Figure 81. D64
Figure 82. D64
Enus , Methods and Settings65
I/O Menu65
4-20Ma Output65
Com Menus and Settings67
Figure 88. a67
Figure 93. H70
Relay Operation, Menus, and Settings71
Menus , Methods , and Settings73
Panel Menu73
Display Menu73
Security Menu74
Menu78
Clock Menu78
Reset Menu78
Version Menu79
Part 5 - Maintenance80
Part 6 - Spare Parts82
Figure 47. D86
Figure 83. D86
Figure 94. H86
Figure 95. M86
Figure 96 a86

ATI Technologies F12/D - Page 50

Table of Contents