AuCom EMX4i - User Manual Emx4 I Soft Starter; Default Chapter; Table of Contents

CONTENTS
710-14888-00C EMX4i User Manual 1
Contents
1. About This Manual ..................................... 3
1.1 Disclaimer ...................................................... 3
2. Caution Statements .................................. 4
2.1 Electrical shock risk ...................................... 4
2.2 Unexpected Operation .................................. 5
2.3 Avertissements à l'attention des clients
canadiens ........................................................ 6
3. System Design ........................................... 8
3.1 Feature List .................................................... 8
3.2 Model Code ..................................................... 9
3.3 Model Selection ............................................. 9
3.4 Current Ratings .......................................... 10
3.5 Dimensions and Weights .......................... 13
3.6 Physical Installation ................................... 14
3.7 Accessories ................................................. 14
3.8 Main Contactor ........................................... 15
3.9 Circuit Breaker ........................................... 15
3.10 Power Factor Correction ........................... 16
3.11 Short Circuit Protection Devices (SCPD) 16
3.12 IEC Coordination with Short Circuit
Protection Devices ..................................... 17
3.13 UL Coordination with Short Circuit
Protection Devices ..................................... 18
3.14 Fuse Selection for Type 2 Coordination .. 21
3.15 Specifications .............................................. 22
3.16 Disposal Instructions ................................. 23
4. Installation ............................................... 24
4.1 Command Source ...................................... 24
4.2 Setup Procedure Overview ....................... 24
4.3 Inputs ............................................................ 25
4.4 Outputs ......................................................... 27
4.5 Control Voltage ........................................... 28
4.6 Power Terminations .................................. 28
4.7 Typical Installation ..................................... 31
4.8 Quick Setup ................................................. 33
5. Setup Tools .............................................. 34
5.1 Set Date and Time ...................................... 34
5.2 Command Source ...................................... 34
5.3 Commissioning ........................................... 34
5.4 Run simulation ............................................ 35
5.5 Load/Save Settings .................................... 36
5.6 USB Save & Load ........................................ 36
5.7 Auto-Start/Stop ........................................... 38
5.8 Network Address ........................................ 38
5.9 Digital I/O State ........................................... 39
5.10 Analog I/O State .......................................... 39
5.11 Serial Number & Rating ............................ 39
5.12 Software Versions ....................................... 40
5.13 Thermistor Reset ........................................ 40
5.14 Reset Thermal Model................................. 40
6. Logs .......................................................... 41
6.1 Event Log ..................................................... 41
6.2 Counters ....................................................... 41
6.3 QR Code ........................................................ 41
7. Keypad and Feedback ............................. 42
7.1 The Keypad .................................................. 42
7.2 Remote Keypad ........................................... 43
7.3 Lighten/Darken the Display ...................... 43
7.4 Starter status LEDs .................................... 44
7.5 Displays ........................................................ 44
8. Operation ................................................. 46
8.1 Start, Stop and Reset Commands ............ 46
8.2 Command Override .................................... 46
8.3 Auto-Start/Stop ........................................... 46
8.4 PowerThrough ............................................ 47
8.5 Emergency Mode ........................................ 48
8.6 Auxiliary Trip ................................................ 48
8.7 Typical Control Methods ............................ 49
8.8 Soft Start Methods ...................................... 50
8.9 Stop Methods .............................................. 53
8.10 Pump Clean ................................................. 57
8.11 Reverse Direction Operation ..................... 57
8.12 Jog Operation .............................................. 58
8.13 Inside Delta Operation ............................... 59
8.14 Secondary Motor Set .................................. 60
9. Programmable Parameters .................. 61
9.1 Main Menu ................................................... 61
9.2 Altering Parameter Values ....................... 61
9.3 Adjustment Lock ......................................... 61
9.4 Parameter List ............................................ 62
9.5 1 Motor Details ............................................ 70
9.6 2 Motor Start/Stop ...................................... 71