AudioCodes Mediant MSBR Series

To Next Page

To Previous Page

Version 6.8 157 Mediant MSBR

Configuration Guide 22. IP Multicast – IGMP Proxy

3. Continue with the streaming wizard.

Figure 22-4 Add Media to Stream

4. From the ‘New destination’ drop-down list, select RTP Audio/Video Profile and then

click Add.

Figure 22-5 Select RTP Audio/Video Profile

Main Page

Default Chapter3
- Table of Contents3
- Abbreviations and Terminology9
- Customer Support9
- Weee Eu Directive9
- Document Revision Record10
- Documentation Feedback10
1 Introduction11
2 Ipv413
- Example of Primary and Secondary IP Address Configuration13
  - Configuration13
  - Output13
- Interface VLAN - Link State Monitor14
  - Configuration14
3 Icmp15
- Ping15
- Traceroute16
4 Vrrp17
- Feature Key17
- CLI Configuration and Status Commands17
  - Configuration Commands17
  - Status Commands17
- VRRP Example19
5 Dhcp27
- DHCP Client27
- DHCP Server28
  - DHCP Zones29
    - Selectors29
    - Default Zone30
- DHCP Relay31
- Example of DHCP Server and DHCP Client32
  - DHCP Client Configuration Example (WAN Side)32
  - DHCP Server Configuration Example (LAN Side)32
- Example of DHCP Relay33
- Example of DHCP Server with Zones33
- Output of Show Commands35
  - Show Dhcp Server Leased Ip Addresses35
  - Show Dhcp Relay Configuration Display35
6 Dns37
- DNS Configuration37
  - Global Configuration37
  - Interface-Specific Configuration37
- Example #1 of Basic Dynamic DNS Configuration38
  - Configuration38
  - Output and Show Commands39
- Example #2 of Basic Static DNS Configuration40
  - Configuration40
7 Track41
- Configuring Track41
- Output41
8 Static Routing43
- Configuring Static Routing43
- Example of Basic Static Route Configuration43
  - Configuration43
  - Output44
- Example of "Floating" Static Route and Track45
  - Configuration45
9 Manipulating the Routing Table47
10 Administrative Distance49
- Examples of Configuring AD for Various Protocols49
- Example of Changing Default AD for a Dynamic Routing Protocol50
  - Configuration50
  - Output50
- Example of Configuring Static Route with Custom Metric51
  - Configuration51
  - Output51
11 Dynamic IP Routing53
- RIP Routing Protocol53
  - Configuring RIP53
  - Example of RIP Routing55
    - Configuration55
    - Output and Show Commands56
- OSPF Routing Protocol57
- Border Gateway Protocol (BGP)62
- Advanced Routing Examples69
12 Policy Based Routing (PBR)75
- PBR Configuration75
  - Example of PBR Using Route-Map-Static75
    - Configuration76
    - Output76
13 Loopback Interfaces79
- Loopback Interface Configuration79
- Example of Loopback Interface Configuration79
14 Virtual Routing and Forwarding (VRF)85
- VRF Configuration85
15 GRE Tunnels91
- Configuring GRE Tunnels91
- Example of Connecting Multiple Subnets Using GRE91
  - Configuration92
  - Output93
16 Quality of Service (Qos)95
- Qos Configuration96
- Example of Weighted Bandwidth Sharing97
17 Ipv6103
- Example of Multiple Ipv6 Address Configuration104
18 Icmpv6107
- Ping Ipv6107
- Traceroute V6108
19 Track V6109
- Configuring Track109
- Output109
20 Ipv6 Routing111
- Static Routing111
  - Configuring Static Routing111
  - Example of a Basic Static Route Configuration111
    - Configuration111
    - Output112
- Ripng Routing Protocol113
  - Configuring Ripng113
  - Example of Ripng Routing114
    - Configuration114
    - Output and Show Commands115
- Ospfv3 Routing Protocol116
- Border Gateway Protocol (BGP) for Ipv6119
- Dchpv6125
- Dnsv6131
  - Dnsv6 Configuration131
    - Global Configuration131
    - Interface-Specific Configuration131
  - Example of Basic Static DNS Configuration132
21 IP Multicast - PIM Sparse Mode133
- Feature Key133
- CLI Configuration and Status Commands133
22 IP Multicast - IGMP Proxy153
- Feature Key153
- CLI Configuration and Status Commands153
A Mediant 500 Transmitter Examples165

AudioCodes Mediant MSBR Series - Page 157

Table of Contents

Other manuals for AudioCodes Mediant MSBR Series

Related product manuals