AudioCodes Mediant MSBR Series

To Next Page

To Previous Page

Configuration Guide A. Mediant 500 Transmitter Examples

Version 6.8 171 Mediant MSBR

This page is intentionally left blank.

Main Page

Default Chapter3
- Table of Contents3
- Abbreviations and Terminology9
- Customer Support9
- Weee Eu Directive9
- Document Revision Record10
- Documentation Feedback10
1 Introduction11
2 Ipv413
- Example of Primary and Secondary IP Address Configuration13
  - Configuration13
  - Output13
- Interface VLAN - Link State Monitor14
  - Configuration14
3 Icmp15
- Ping15
- Traceroute16
4 Vrrp17
- Feature Key17
- CLI Configuration and Status Commands17
  - Configuration Commands17
  - Status Commands17
- VRRP Example19
5 Dhcp27
- DHCP Client27
- DHCP Server28
  - DHCP Zones29
    - Selectors29
    - Default Zone30
- DHCP Relay31
- Example of DHCP Server and DHCP Client32
  - DHCP Client Configuration Example (WAN Side)32
  - DHCP Server Configuration Example (LAN Side)32
- Example of DHCP Relay33
- Example of DHCP Server with Zones33
- Output of Show Commands35
  - Show Dhcp Server Leased Ip Addresses35
  - Show Dhcp Relay Configuration Display35
6 Dns37
- DNS Configuration37
  - Global Configuration37
  - Interface-Specific Configuration37
- Example #1 of Basic Dynamic DNS Configuration38
  - Configuration38
  - Output and Show Commands39
- Example #2 of Basic Static DNS Configuration40
  - Configuration40
7 Track41
- Configuring Track41
- Output41
8 Static Routing43
- Configuring Static Routing43
- Example of Basic Static Route Configuration43
  - Configuration43
  - Output44
- Example of "Floating" Static Route and Track45
  - Configuration45
9 Manipulating the Routing Table47
10 Administrative Distance49
- Examples of Configuring AD for Various Protocols49
- Example of Changing Default AD for a Dynamic Routing Protocol50
  - Configuration50
  - Output50
- Example of Configuring Static Route with Custom Metric51
  - Configuration51
  - Output51
11 Dynamic IP Routing53
- RIP Routing Protocol53
  - Configuring RIP53
  - Example of RIP Routing55
    - Configuration55
    - Output and Show Commands56
- OSPF Routing Protocol57
- Border Gateway Protocol (BGP)62
- Advanced Routing Examples69
12 Policy Based Routing (PBR)75
- PBR Configuration75
  - Example of PBR Using Route-Map-Static75
    - Configuration76
    - Output76
13 Loopback Interfaces79
- Loopback Interface Configuration79
- Example of Loopback Interface Configuration79
14 Virtual Routing and Forwarding (VRF)85
- VRF Configuration85
15 GRE Tunnels91
- Configuring GRE Tunnels91
- Example of Connecting Multiple Subnets Using GRE91
  - Configuration92
  - Output93
16 Quality of Service (Qos)95
- Qos Configuration96
- Example of Weighted Bandwidth Sharing97
17 Ipv6103
- Example of Multiple Ipv6 Address Configuration104
18 Icmpv6107
- Ping Ipv6107
- Traceroute V6108
19 Track V6109
- Configuring Track109
- Output109
20 Ipv6 Routing111
- Static Routing111
  - Configuring Static Routing111
  - Example of a Basic Static Route Configuration111
    - Configuration111
    - Output112
- Ripng Routing Protocol113
  - Configuring Ripng113
  - Example of Ripng Routing114
    - Configuration114
    - Output and Show Commands115
- Ospfv3 Routing Protocol116
- Border Gateway Protocol (BGP) for Ipv6119
- Dchpv6125
- Dnsv6131
  - Dnsv6 Configuration131
    - Global Configuration131
    - Interface-Specific Configuration131
  - Example of Basic Static DNS Configuration132
21 IP Multicast - PIM Sparse Mode133
- Feature Key133
- CLI Configuration and Status Commands133
22 IP Multicast - IGMP Proxy153
- Feature Key153
- CLI Configuration and Status Commands153
A Mediant 500 Transmitter Examples165

AudioCodes Mediant MSBR Series - Page 171

Table of Contents

Other manuals for AudioCodes Mediant MSBR Series

Related product manuals