Home
AUMA
Controller
AM 01.1
AUMA AM 01.1 User Manual
4
of 1
of 1 rating
84 pages
Give review
Manual
Specs
To Next Page
To Next Page
To Previous Page
To Previous Page
Loading...
3.
Apply a thin film of non-acidic grease (e.g.
petroleum jelly) to the O-ring and
inser
t it correctly
.
4.
Place cover [1] on s
witch compar
tment.
5.
F
asten screws [2] e
venly cross
wise.
60
SA 07.2
–
SA 16.2 /SAR 07.2
–
SAR 16.2
Commissioning
–
controls settings
AM 01.1/AM 02.1
59
61
Table of Contents
Default Chapter
2
Table of Contents
2
1 Safety Instructions
5
Basic Information on Safety
5
Range of Application
5
Applications in Ex Zone 22 (Option)
6
Warnings and Notes
6
References and Symbols
7
2 Identification
8
Name Plate
8
Sar 07.2 Sar
10
Short Description
11
3 Transport, Storage and Packaging
12
Transport
12
Storage
14
Packaging
15
4 Assembly
16
Mounting Position
16
Handwheel Fitting
16
Multi-Turn Actuator: Mount to Valve/Gearbox
16
Output Drive Type a
16
4.3.1.1. Stem Nut: Finish Machining
17
4.3.1.2. Multi-Turn Actuator (with Output Drive Type A): Mount to Valve
18
Output Drive Types B and E
19
Multi-Turn Actuator with Output Drive Types B: Mount to Valve/Gearbox
20
Accessories for Assembly
21
Stem Protection Tube for Rising Valve Stem
21
Mounting Positions of Local Controls
22
Mounting Positions: Modify
23
5 Electrical Connection
24
Basic Information
24
Electrical Connection S/SH (AUMA Plug/Socket Connector)
26
Terminal Compartment : Open
27
Cable Connection
28
Terminal Compartment : Close
29
Accessories for Electrical Connection
30
Actuator Controls on Wall Bracket
30
Parking Frame
31
DS Intermediate Frame for Double Sealing
31
External Earth Connection
32
Operation
33
Manual Operation
33
Engage Manual Operation
33
Manual Operation: Disengage
33
Motor Operation
34
Local Operation
34
Actuator Operation from Remote
35
Indications
36
Indication Lights
36
Optional Indications
36
Mechanical Position Indication Via Indicator Mark
36
Signals (Output Signals)
38
Status Signals Via Output Contacts (Digital Outputs)
38
Optional Signals
38
Analogue Signals (Analogue Outputs)
38
Commissioning (Basic Settings)
39
Heat-Up Time for Low Temperature Version
39
Switch Compartment: Open
39
Torque Switching: Set
40
Limit Switching: Set
40
End Position CLOSED (Black Section): Set
41
End Position OPEN (White Section): Set
41
Intermediate Positions: Set
42
Running Direction CLOSE (Black Section): Set
42
Running Direction OPEN (White Section): Set
42
Test Run
43
Direction of Rotation at Mechanical Position Indicator: Check
43
Direction of Rotation at Hollow Shaft/Stem: Check
43
Limit Switching: Check
44
PTC Tripping Device (Option): Test
45
Switch Compartment: Close
45
Commissioning (Optional Equipment Settings)
46
EWG 01.1 Electronic Position Transmitter
46
Measuring Range: Set
47
Current Values : Adjust
47
LED End Position Signalling: Switch On/Off
48
Potentiometer
48
Potentiometer: Set
48
RWG Electronic Position Transmitter
49
Measuring Range: Set
49
Mechanical Position Indicator: Set
50
Commissioning Controls Settings
51
Actuator Controls: Open
51
Type of Seating: Set
51
Push-To-Run Operation or Self-Retaining: Set
52
Running Indication (Blinker Transmitter): Activate/Deactivate
53
Torque Fault in Collective Fault Signal: Activate/Deactivate
53
Leds for Torque Fault, Phase Failure, Motor Protection
53
Positioner
54
Input Ranges (Signal Type) for Setpoint and Actual Value
54
Behaviour on Loss of Signal (Actuator Reaction)
55
Adjustment in End Positions
56
Sensitivity Setting
58
EMERGENCY Command (EMERGENCY - OPEN/EMERGENCY - CLOSE)
59
Actuator Controls: Close
59
Corrective Action
61
Faults During Operation/Commissioning
61
Fuses
61
Fuses Within the Actuator Controls
61
Motor Protection (Thermal Monitoring)
63
Servicing and Maintenance
65
Preventive Measures for Servicing and Safe Operation
65
Maintenance
66
Disposal and Recycling
66
Technical Data
67
Technical Data Multi-Turn Actuators
67
Technical Data Actuator Controls
70
Spare Parts
73
Multi-Turn Actuators SA(V)
73
Sa(V) 16.2/Sar(V) 07.2
73
Sar(V) 16.2
73
Actuator Controls am 01.1/AM
75
Certificates
77
Declaration of Incorporation and EU Declaration of Conformity
77
Index
78
Addresses
81
4
Based on 1 rating
Ask a question
Give review
Questions and Answers:
Need help?
Do you have a question about the AUMA AM 01.1 and is the answer not in the manual?
Ask a question
AUMA AM 01.1 Specifications
General
Brand
AUMA
Model
AM 01.1
Category
Controller
Language
English
Related product manuals
AUMA MATIC AM 01.1
20 pages
AUMA AM 02.1
92 pages
AUMA MATIC AM 02.1
108 pages
AUMA AMB 01.1
96 pages
AUMA Aumatic ACExC 01.1
68 pages
AUMA ACV 01.2
168 pages
AUMA ABG 10.2
12 pages
AUMA AUMATIC AC 01.2
92 pages
AUMA ACVExC 01.2 Series
144 pages
AUMA AUMATIC ACExC 01.2
92 pages
AUMA ACE C 01.2 Profinet Series
76 pages
AUMA SA 07.6
104 pages
To Next PageTo Next PageTo Previous PageTo Previous Page
Loading...
Need help?
General
