EN55022-CISPR22 Class B ITE (Information Technology Equipment)
This is a class B product. In a domestic environment this product may c ause radio interference in which cas e the user may be required to
take adeq uate meas ures.
If this eq uipment does cause interference to radio or television reception, the user may try to correct the interference by one or more of the
following meas ures :
• Re-orientation of the receiving antenna for the radio or television.
• Relocate the equipment with respect to the rece iver.
• Plug the equipm ent into a different outlet so that the equipme nt and receiver are on different branc h circuits.
• Fasten cables c onnectors to the equipment by mounting sc rews.
Federal Communication Commission Interference S tatement
You are cautioned that changes or modifications not expressly approved by the part r esponsible for compliance coul
d void the user’s
authority to operate the equipme nt.
This equipment has been tested and found to comply with the limits for a C lass B d igital device, pursuant to Part 15 of the FCC rules.
These limits are designed to pro vide reasonable protection against har mful interference in a residential installation. This eq uipment ge n-
erates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, m ay cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is enc ouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is conn ected.
• Consult the dealer or an experienced radio/TV techn ician for help.
You ma y als o find helpful the following booklet, prepared by the FCC: "How to Identify and Resolve Radio-TV Interference Prob lems." T his
booklet is a vailable from the U.S. Government Printing Office, Washington D.C. 20402.
Changes and Modifications n ot expressly approved by the m anufacturer or regis trant of this equipment can void your a uthority to operate
this equipment under Federal Communica tions Com mis sions rules.
In order to maintain compliance with FCC regulations shielded cables m ust be used with this equipment. Operation with non-approved
equipment or unshielded cables is likely to result in interference to radio & television reception.
FCC RF Radiation Exposure Statement: This device is capable of operating in 802.11a mode. For 802.11a devices operating in the
frequency range of 5.15 - 5.25 GHz, they ar e restricted for indoor operations to red uce any potential harmful interference for Mo bile Satellite
Services (MSS) in the US. W IFI Acc ess Points that are capable of allowing your device to op erate in 802.11a mode (5 .15 - 5.25 GHz band)
are optimized for indoor use only. If y our WIFI network is capable of operating in this mode, please restrict y our W IFI use indoors to not
violate federal regulations to protect Mobile Satellite Services.
Base Unit FC C ID: 2AAED-R9861520
Button FCC ID (model R9861006D01): XF6-RS9110N1103
Button FCC ID (model R9861500D01): 2AAED-R9861500D01
ClickShare Button R9861500D0 1 has been tested and meets the FCC RF ex posure guidelines.The maximum SA R value reported is
0.915W/kg.
Canada, Industry Canada (IC) Notices
This device complies with Industry Ca nada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this
device m ay not c ause interference, and (2) this devic e must acce pt any interference, including interference that may caus e undesired
operation of the device.
Radio Frequency (RF) Exposure Information
The radiated output power of the Barco Wireless D evice is below the Indus try Canada (IC) r adio frequency exposure limits. The Barco
Wireless Device should be used in such a m anner such that the potential for hum an contact during n ormal operation is minimized.
Base Unit IC ID: IC: 9393B -R9861520
Button IC ID (model R9861006D01): 8407A-RS9110N1103
Button IC ID (model R9861500D01): 9393B-R98615
00D01
To Next Page
Loading...
Need help?
General
