BIFFI ICON 2000 - Page 263

“ICON 2000v4"
instruction and operating manual
© Copyright by BIFFI Italia. All right reserved. Section 618/42 Page 32
Contents may change without notice
Ext_User_Prm_Data_Const(1)=0
Ext_User_Prm_Data_Const(2)=0
Ext_User_Prm_Data_Ref(3)=1
Ext_User_Prm_Data_Ref(4)=2
Ext_User_Prm_Data_Ref(5)=3
Ext_User_Prm_Data_Ref(6)=4
Ext_User_Prm_Data_Ref(7)=5
Ext_User_Prm_Data_Ref(8)=7
Ext_User_Prm_Data_Ref(9)=8
Ext_User_Prm_Data_Ref(10)=9
Ext_User_Prm_Data_Ref(11)=10
Ext_User_Prm_Data_Ref(12)=6
Ext_User_Prm_Data_Ref(13)=7
Ext_User_Prm_Data_Ref(14)=8
Ext_User_Prm_Data_Ref(15)=11
Ext_User_Prm_Data_Ref(16)=12
Ext_User_Prm_Data_Const(17)=0
Ext_User_Prm_Data_Ref(18)=13
Ext_User_Prm_Data_Ref(19)=14
;
;
Modular_Station=1
Max_Module=1
Max_Input_Len=8
Max_Output_Len=4
Max_Data_Len=12
;
; Slave-Specification:
;
DPV1_Slave=1
;
C1_Read_Write_supp=0
C2_Read_Write_supp=1
C2_Max_Data_Len=240
C2_Response_Timeout=100
C2_Read_Write_required=0
C2_Max_Count_Channels=3
Max_Initiate_PDU_Length=72
Diagnostic_Alarm_supp=0
Process_Alarm_supp=0
Pull_Plug_Alarm_supp=0
Status_Alarm_supp=0
Update_Alarm_supp=0
Manufacturer_Specific_Alarm_supp=0
Extra_Alarm_SAP_supp=0
Alarm_Sequence_Mode_Count=0
Alarm_Type_Mode_supp=0
Diagnostic_Alarm_required=0
Process_Alarm_required=0
Pull_Plug_Alarm_required=0
Status_Alarm_required=0
Update_Alarm_required=0
Manufacturer_Specific_Alarm_required=0
DPV1_Data_Types=0
WD_Base_1ms_supp=1
Check_Cfg_Mode=0
;
;Device related Diagnosis
;
Unit_Diag_Bit(24)="Motor Thermostat"
Unit_Diag_Bit(25)="HI-HI Torque in Opening"
Unit_Diag_Bit(26)="HI-HI Torque in Closing"
Unit_Diag_Bit(27)="Actuator blocked in Opening"
Unit_Diag_Bit(28)="Actuator blocked in Closing"
Unit_Diag_Bit(29)="HI-HI Temperature"
Unit_Diag_Bit(30)="Postition Sensor Failure"
Unit_Diag_Bit(31)="Speed Sensor Failure"
Unit_Diag_Bit(32)="Main Voltage Fault"
Unit_Diag_Bit(33)="K1 Contactor Failure"
Unit_Diag_Bit(34)="K2 Contactor Failure"
Unit_Diag_Bit(35)="Configuration Error"
Unit_Diag_Bit(36)="Hardware Error"
Unit_Diag_Bit(37)="Low Alkaline Battery"
Unit_Diag_Bit(38)="Lost Phase"
Unit_Diag_Bit(39)="No response from base card"
;
; Module Definition List