BIS VISTA - Page 34

To Next Page

To Previous Page

SECTION 2 INSTALLATION AND PREPARATION FOR USE

______________________________________________________________________

2-14

Settings are set and saved for the current Monitor Mode only. See 3.5.10 “Monitor Mode.”

See Section 3.5.6 “View/Save Settings” for instructions on restoring factory default values.

Main Page

Table of Contents5
About this Manual10
Introducing the bis Vista Monitoring System11
Safety Precautions13
Warnings13
Cautions15
Key to Symbols18
Figure 1 - Symbol Key18
Installation and Preparation for Use21
BIS VISTA Monitor Installation and Checkout21
Environment22
Shipping and Storage Environment22
Operating Environment22
Power Requirements and System Grounding23
Electromagnetic Compatibility Requirements23
Site Preparation: Mounting the Monitor24
Mounting the Monitor Using the Pole Clamp24
Figure 2 - Pole Clamp24
Optional Mounting Accessories25
The bis VISTA Monitoring System - Equipment and Supplies26
Figure 3 - the bis VISTA Monitoring System26
BIS VISTA Monitor27
Front Panel27
Touch Screen27
On/Standby Button27
Rear Panel27
Figure 4 - Rear Panel28
Integral Battery29
Bisx30
Figure 5 - Bisx and PIC30
Patient Interface Cable (PIC)31
BIS Sensors31
Cable Connections31
Start Procedure / Standby Mode32
Starting the Monitor for the First Time32
Starting the Monitor from Standby Mode32
Initial Menu Settings32
Language Selection33
Date and Time33
View/Save Settings33
Operating the bis Vista Monitoring System35
Preparing for Operation35
Sensor Check37
Figure 6 - Connecting the PIC37
Figure 7 - Sensor Check Graphic Screen (Values Not Shown)38
Figure 8 - Sensor Check Graphic Screen with Values Shown39
BIS Trend Data Screen40
BIS (Bispectral Index) Value40
Signal Quality Indicator40
Figure 9 - Screen Features - bis Trend Data Screen40
Electromyograph (EMG) Indicator41
EEG Waveform Display41
Message Region41
BIS Trend Graph42
Additional Screen Information43
Battery Icon43
USB Export Icon43
Print Icon44
Extend Mode44
Suppression Ratio (SR) Number44
Burst Count (Bursts/Minute)44
Main Screen Touch Keys45
Alarm Touch Keys45
Figure 11 - Alarm Touch Keys45
Menu, Home, Sensor Check and Review Touch Keys46
Figure 12 - Menu, Home, Sensor Check and Review Mode Touch Keys46
Menu Selections47
Target Range47
Figure 13 - Target Range47
Secondary Variable49
Figure 14 - Secondary Variable49
Chart Data50
Figure 15 - Chart Data50
Alarm Volume51
Figure 16 - Alarm Volume51
BIS/EEG Display Modes52
View/Save Settings52
Figure 17 - BIS/EEG Display Modes52
Figure 18 - View/Save Settings52
Help53
Figure 19 - Help53
Snapshot54
Display Suppression Ratio (SR)54
Figure 20 - Snapshot54
Figure 21 - Display SR54
Monitor Mode55
Figure 22 - Monitor Mode Settings55
Export Data56
Figure 23 - Export Data56
BIS Smoothing Rate58
Figure 24 - Smoothing Rate58
Print (Snapshot)59
Figure 25 - "Print" Touch Key59
Configuration Information60
EEG Channels60
Figure 26 - Configuration Information60
Figure 27 - EEG Channels60
Date and Time61
Figure 28 - Date and Time61
Language62
Filters62
Figure 29 - Language Menu62
Figure 30 - Filters62
Impedance Checking63
Figure 31 - Impedance Checking ON/OFF63
Maintenance Menu64
Demo Case64
Diagnostic Menu64
Reviewing and Printing Stored Trend Data65
Review Mode Touch Keys65
Figure 32 - Review Screen (Case Mode)65
Figure 33 - Review Screen (Cursor Mode)66
Printing Stored Data67
EEG Display68
Ending a Case68
Figure 34 - EEG Display68
Data Transfer69
How the bis VISTA Monitoring System Works70
Figure 35 - bis Range Guidelines70
Bispectral Index (BIS)71
Artifact Detection71
System Self-Checks71
Monitor Data Memory72
Bisx Data Memory72
Battery Operation73
Quick Reference Guide75
Preventive Maintenance, Care and Cleaning77
Care and Cleaning77
Maintenance78
Replace the PIC (Patient Interface Cable)78
Checking Cable Integrity79
System Checkout79
Checking the Battery80
Replacing the Battery80
Replacing the Power Supply81
Figure 36 - Replacing the Power Supply81
Checking Leakage Current82
Technical Documentation83
Instrument Identification83
Diagnostics and Troubleshooting85
Maintenance Menu85
Display Bisx Connection History85
Serial Protocol85
Software Update86
Restore Default Settings for All Modes86
Calibrate Touch Screen86
Diagnostic Menu87
Diagnostic Codes87
DSC Self Test87
Figure 37 - Diagnostic Codes ON/OFF87
BIS VISTA System Messages and Corrective Actions88
Using the Reset Button95
What to Do if the bis VISTA Monitoring System Requires Service95
Appendix I: Menus, Processed Variables and Glossary97
Menu Map97
Figure 38 - bis VISTA Menu Map97
Menu Listing98
Processed EEG Variables100
Glossary101
Appendix II: Specifications, Warranty and Software License Agreement103
Specifications103
Electromagnetic Compatibility Specifications107
Accessories107
Warranty113
Software License Agreement115

BIS VISTA - Page 34

Table of Contents