9-4
Bosch Security Systems 05/10 BLCC100I
Solution 16
plus
Installation Manual Comms Programming
2) Using the numeric keys, enter all the digits of the telephone
number. You can change a single digit by scrolling the cursor
left or right. For special characters including, pause, * or #, use
the up and down arrow keys.
3) Press [OK] to save and exit or press [MENU] to exit without
saving.
Comms > Telephone Number >
Domestic
-
MENU 5-1-5
First
Number
1 Digits 32
Second
Number
1 Digits 32
Third
Number
1 Digits 32
Refer to Menu 5-0-0 for instructions on Domestic Phone Number
setup.
Up to 3 Phone numbers can be entered for Domestic dialing.
Press [OK] after each telephone number is entered to save and
move to the next number.
Comms > Telephone Number >
Call Forward On
-
MENU 5-1-6
1 Digits 32
•
6 1 , * 2 0 #
The panel is able to activate certain Telco services such as
Call Forwarding when the system is armed. Call forwarding
means that your customer will no longer need to remember to
manually activate the Call Forward On feature via the telephone
before leaving.
MENU 5-1-6 allows you to program the Call Forward On number
sequence. When armed the panel will automatically seize the
phone line and dial the number sequence and then hang up.
In Australia, a typical sequence for activating the Call-Forward
On feature (All Calls) might be:
*61 0416123456 *20 #
*61 diversion type - Call Forward On - Immediate.
0416123456 Telephone number that you want calls to be
diverted to. Example shows mobile number.
*20 20 second delay
# end of sequence
1) Enter [MENU] + [5] + [1] + [6]. The keypad will display any
current Call Forward sequnces.
Call Forward On P001
*61,*20#
Press 0-9 OK to SAVE
2) Using the numeric keys, enter all digits for the sequence. You
can change a single digit by scrolling the cursor left or right.
For special characters including, pause, * or #, use the up and
down arrow keys.
3) Press [OK] to save and exit or press [MENU] to exit without
saving.
Comms > Telephone Number >
Call Forward Off
-
MENU 5-1-7
1 Digits 32
# 6 1 #
The panel is also able to deactivate certain Telco services such as
Call Forwarding when the system is disarmed. This means that
your customer will no longer need to remember to manually
deactivate Call Forwarding when they disarm the system.
MENU 5-1-7 allows you to program the Call Forward O number
sequence. When disarmed the panel will automatically seize the
phone line and dial the number sequence and then hang up.
In Australia, a typical sequence for deactivating the Call-Forward
On feature (All Calls) might be:
*61 = diversion type - Call Forward On - Immediate.
# = end of sequence
1) Enter [MENU] + [5] + [1] + [7]. The keypad will display any
current Call Forward O sequences.
Call Forward Off P001
#61#
Press 0-9 OK to SAVE
2) Using the numeric keys, enter all digits for the sequence. You
can change a single digit by scrolling the cursor left or right.
For special characters including, pause, * or #, use the up and
down arrow keys.
3) Press [OK] to save and exit or press [MENU] to exit without
saving.
COMM S P ROP E RT IES
Comms > Properties >
Call Attempt Count
MENU 5-2-0
0 6
This menu programs the maximum number of call attempts the
panel will make per destination in order to deliver the report
signal.
At factory default, the maximum number of call attempts
per event is 6 when reporting to a single destination and 12
attempts when reporting to 2 destinations. (6 attempts per
destination)
Domestic dialling also follows the call attempt count. However,
the call attempt count will be spread over total phone numbers
programmed for domestic reporting, ie. if three domestic
telephone numbers are programmed and the call attempt
To Next Page
Loading...
Need help?
General
