What does 'Cannot Fit' mean when there are too many lines of text on Brady Label Maker?
The “Cannot Fit” error indicates that there are too many lines of text. The maximum number of lines allowed is four, but it may be less when using pre-sized labels. A blank line is considered another line of text, so avoid pressing ENTER at the end of a line if you don't want another line.
How to fix a Brady M210 Label Maker when it's jammed and won't feed labels?
If your Brady Label Maker is jammed, it's likely due to a blocked label exit chute causing label material to back up inside the printer. Here’s how to clear the jam: * Slide the locking lever to the unlock position (you might need to force it if there's a large jam). * Remove the cartridge. * Use tweezers or needle-nose pliers to carefully clear the label jam. Be careful not to damage the print head.
What to do if Brady M210 screen freezes?
If your Brady Label Maker screen freezes, it could be due to a user interface error. First, try pressing the Power button to turn the printer off. If that doesn't work, remove the AC adapter (if you're using one), then remove the battery pack or batteries, and immediately re-insert them. Finally, power the printer back on.
What to do if my Brady Label Maker is not responding?
If your Brady Label Maker is not responding, it's likely because the battery is dead. If you're using a lithium-ion battery, remove it from the printer and recharge it using the AC adapter. Alternatively, you can install 6 new AA batteries in the battery compartment to use the printer while the lithium-ion battery is recharging.
How to resolve poor print quality due to dust on my Brady Label Maker?
If you're experiencing poor print quality with your Brady Label Maker, it could be due to dust or adhesives accumulated on the print head. Clean the print head.
Why doesn't my Brady Label Maker menu display all label types?
The Brady Label Maker only displays label types that are compatible with the installed label material (cartridge). Fewer label types are supported when using pre-sized cartridges. Insert the correct label material (cartridge) for the labels you want to produce.
Can I change the position of the human-readable text in a barcode on my Brady M210?
The human readable text is automatically added below the barcode on your Brady Label Maker. This position is fixed and cannot be changed.
How to add a checksum character in a barcode on my Brady M210 Label Maker?
The Brady Label Maker does not allow checksum characters to be used in barcodes.
What does the error 'Cut while printing' mean on my Brady Label Maker?
The 'Cut while printing' error on your Brady Label Maker means that you operated the cutter while labels were still printing. Cut through the material completely, press the Clear key to clear the error, and then reprint the label(s).
Why does my Brady Label Maker LCD go back to the previous label text?
If your Brady Label Maker LCD reverts to the previous label text, it's likely because the battery is low. If you're using batteries, replace them with 6 new AA batteries. Alternatively, if you're using the lithium-ion battery, remove it from the printer and recharge it using the AC adapter.
General| Product color | Black, Yellow |
|---|---|
| Internal memory | 16 MB |
| Built-in barcodes | Code 39, Data Matrix, QR Code |
| Color | No |
| Print technology | Thermal transfer |
| Maximum resolution | 203 x 203 DPI |
| Maximum printing width | 16 mm |
| Battery type | Built-in battery |
| AC input voltage | 110 - 240 V |
| Maximum label width | 19.05 mm |
| USB port | - |
| Connectivity technology | Wireless |
Weight and Dimensions| Depth | 63 mm |
|---|---|
| Width | 114 mm |
| Height | 241 mm |
| Weight | 750 g |
Safety precautions and warnings related to battery usage and handling.
Step-by-step instructions for removing and installing label cartridges.
Troubleshooting common hardware issues with the printer.
Steps to resolve issues where the printer screen freezes.
How to fix print quality issues like void areas or lines on text.
Instructions for cleaning internal components like the print head and platen roller.
To Next Page
