What does 'No / Invalid Cartridge' mean on my Brady M210?
The “No / Invalid Cartridge” error on your Brady Label Maker means that no cartridge is installed, or a non-Brady brand cartridge is installed, or the circuit board on the label/media roll is damaged. Verify that the installed Brady media cartridge has the Authentic logo. Replace the label/media roll and press the CLEAR/ESC key to clear the error.
What to do if my Brady M210 Label Maker does not turn on?
If your Brady Label Maker isn't powering on, the battery pack might not be charged. If you're using batteries, replace them with 6 new AA batteries. If you're using a lithium-ion battery, remove it from the printer and recharge it using the AC adapter. You can also insert 6 AA alkaline batteries in the battery compartment to use the printer while the lithium-ion battery is charging.
What does 'Check Cartridge / Lever' mean on my Brady Label Maker?
The “Check Cartridge / Lever” error on your Brady Label Maker indicates that the locking lever might not be engaged, the cartridge is empty, or the label is jammed. Verify that the locking lever is in the correct position. If not, insert a new cartridge. If there is a jam, remove the cartridge, cut off the damaged portion, and reinsert the cartridge.
Why does my Brady Label Maker LCD go back to the previous label text?
If your Brady Label Maker LCD reverts to the previous label text, it's likely because the battery is low. If you're using batteries, replace them with 6 new AA batteries. Alternatively, if you're using the lithium-ion battery, remove it from the printer and recharge it using the AC adapter.
What does 'Error' mean on my Brady M210 Label Maker LCD screen?
If your Brady Label Maker LCD screen displays “Error”, it could be due to a low battery, incorrect media, or a motor issue. Try replacing the batteries with 6 new AA batteries, or recharge the lithium-ion battery using the AC adapter. Also, ensure you're using the correct media cartridge. If the error persists after these steps, the printer may need repair.
How to resolve void areas or lines due to ribbon wrinkling on my Brady Label Maker?
If you're seeing void areas or lines in your printed text, it might be caused by ribbon wrinkling. Remove the cartridge and advance the ribbon by rotating the take-up spool clockwise until the wrinkled or damaged ribbon is no longer visible (typically one or two full turns). Reinstall the cartridge and continue printing. Alternatively, try a new cartridge.
What to do if nothing happens when I press Print on my Brady Label Maker?
If nothing feeds out when you press Print on your Brady Label Maker, make sure the locking lever is in the correct position. Also, try inserting a different label cartridge and verify that the exit chute isn't blocked.
Why won't my Brady Label Maker feed labels?
If your Brady Label Maker won't feed labels, it could be due to an uneven or torn leading edge on the label roll, or the locking lever not being engaged. Use scissors to cut a straight leading edge on the label roll and verify that the locking lever is in the correct position.
How to resolve poor print quality due to dust on my Brady Label Maker?
If you're experiencing poor print quality with your Brady Label Maker, it could be due to dust or adhesives accumulated on the print head. Clean the print head.
What to do if my Brady Label Maker is not responding?
If your Brady Label Maker is not responding, it's likely because the battery is dead. If you're using a lithium-ion battery, remove it from the printer and recharge it using the AC adapter. Alternatively, you can install 6 new AA batteries in the battery compartment to use the printer while the lithium-ion battery is recharging.
Safety precautions and warnings related to battery usage and handling.
Step-by-step instructions for removing and installing label cartridges.
Troubleshooting common hardware issues with the printer.
Steps to resolve issues where the printer screen freezes.
How to fix print quality issues like void areas or lines on text.
Instructions for cleaning internal components like the print head and platen roller.
General| Product color | Black, Yellow |
|---|---|
| Internal memory | 16 MB |
| Built-in barcodes | Code 39, Data Matrix, QR Code |
| Color | No |
| Print technology | Thermal transfer |
| Maximum resolution | 203 x 203 DPI |
| Maximum printing width | 16 mm |
| Battery type | Built-in battery |
| AC input voltage | 110 - 240 V |
| Maximum label width | 19.05 mm |
| USB port | - |
| Connectivity technology | Wireless |
Weight and Dimensions| Depth | 63 mm |
|---|---|
| Width | 114 mm |
| Height | 241 mm |
| Weight | 750 g |
To Next Page
