EasyManua.ls Logo

Buell X1 2002 - Page 29

Buell X1 2002
462 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
2002 Buell X1: Maintenance 1-7
HOME
Condition of rear brake caliper mounting pins and boots IL IL IL IL IL IL
Tire pressure and inspect tire for wear/damage
(
1.9 TIRES AND WHEELS)
IIIIIIIIIIIIIII Check pressure when tires are cold.
Wheel bearings (
1.9 TIRES AND WHEELS) I I I I Check for wear and corrosion. Replace in sets only.
Primary drive/transmission fluid (
1.10 CLUTCH)
REAR WHEEL SUPPORT STAND (Part No. B-41174)
R IRIRIRIRIRIR Fluid type and amount
1.0 quart (0.95 liter) of SPORT-TRANS FLUID (Part No. 98854-96)
Fluid level
Fluid should reach bottom of clutch spring with motorcycle upright
(not on side stand).
Drain plug torque
14-21 ft-lbs (19.0-28.5 Nm)
Clutch adjustment (1.10 CLUTCH)
A A A A A A A Hand lever freeplay
1/16-1/8 in. (1.6-3.2 mm)
Clutch inspection cover screw torque
7-9 ft-lbs (9.5-12.2 Nm) in a crosswise pattern
Drive belt deflection (
1.11 DRIVE BELT DEFLECTION)
BELT TENSION GAUGE (Part No. HD-35381)
IA I I I I I I Belt deflection with 10 lbs (4.5 kg) of upward force (suspension
unloaded)
1.50-1.75 in. (38.1-44.5 mm)
Rear axle nut torque
68-73 ft-lbs (89.5-98.9 Nm)
Primary chain (
1.13 PRIMARY CHAIN)
I I I I I I I Chain freeplay with hot engine
1/4-3/8 in. (6.4-9.5 mm)
Chain freeplay with cold engine
3/8-1/2 in. (9.5-12.7 mm)
Inspection screws torque
40-60 in-lbs (4.5-6.8 Nm)
Rear shock absorber (
1.15 SUSPENSION DAMPING ADJUSTMENTS)
I I I I I I I Check for bushing wear and loose mounting hardware.
SERVICE OPERATIONS
AND SPECIAL TOOLS
P
R
E
R
I
D
E
5
0
0
MI
8
0
0
K
M
2
5
0
0
MI
4
0
0
0
K
M
5
0
0
0
MI
8
0
0
0
K
M
7
5
0
0
MI
1
2
0
0
0
K
M
1
0
0
0
0
MI
1
6
0
0
0
K
M
1
2
5
0
0
MI
2
0
0
0
0
K
M
1
5
0
0
0
MI
2
4
0
0
0
K
M
1
7
5
0
0
MI
2
8
0
0
0
K
M
2
0
0
0
0
MI
3
2
0
0
0
K
M
2
2
5
0
0
MI
3
6
0
0
0
K
M
2
5
0
0
0
MI
4
0
0
0
0
K
M
2
7
5
0
0
MI
4
4
0
0
0
K
M
3
0
0
0
0
MI
4
8
0
0
0
K
M
A
N
N
U
A
L
SERVICE DATA
Table Code:
A - Adjust.
I - Inspect, and if necessary, correct, adjust, clean or replace.
L - Lubricate with specified lubricant.
R - Replace or change.
T - Tighten to proper torque.
X - Perform.

Table of Contents

Related product manuals