EasyManuals Logo

CompAir DELCOS XL Series User Manual

CompAir DELCOS XL Series
80 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #61 background imageLoading...
Page #61 background image
Base Load Sequencing (BLS) 10
October 2013 GB 61 /80
Electronic Controller Minimum
Required Soft-
ware Versions
DELCOS XL-D DXL-D-1.00
DELCOS XL-DRS DXL-DRS-1.00
DELCOS XL-DH DXL-DH-1.00
DELCOS XL-DHRS DXL-DHRS-1.00
DELCOS XL-L DXL-L-1.02
DELCOS XL-LRS DXL-LRS-1.04
DELCOS PRO-L DPro-L-1.18
DELCOS PRO-LRS DPro-LRS-1.02
DELCOS PROG-LSR DPro-LSR-1.05
DELCOS 3100-L SD31V2.05
DELCOS 3100-LRS SD31R2.03
DELCOS 3100-LRS (V2) D31RS1.06
DELCOS 3100-LSR SD31S1.16
DELCOS 3100-DH HD31V2.05
DELCOS 3100-DHRS HD31R1.34
DELCOS 3100-DHSR HD31S1.22
Chart 10-2: Required Software Versions
The software version can be checked in the con-
troller menu structure. More detailed information is
contained in the operating instructions of the rele-
vant controller.
When a software update is necessary, contact
Gardner Denver.
10.3
Menu "Base Load Sequencing"
Activating and deactivating base load se-
quencing
1
Tap the <Access Code> tab.
The input mask "Access Code" opens.
2 Tap the <Number buttons> to enter the access
code "1234".
3 If necessary, make any corrections with the
<Back> button.
4 Tap the <Enter> button.
Base load sequencing is activated.
The <Base Load Sequencing> tab is dis-
played.
Hours On-load
Home
Hours Run
Hours to next Service
Remote Start Enabled
Timer start enabled
Auto. Restart Enabled
On-load 2600rpm
Mo.
1
Fig. 10-1: Menü "Home" with tab <Base Load Sequenc-
ing>
To deactivate base load sequencing enter the
same access code again.
NOTE
The Base Load Sequencing feature can be ac-
tivated even if the RS485:3 module is not in-
stalled. In this case, you will get a communica-
tion fault message because the master cannot
establish communication with the slaves, as they
are not connected. See chapter "Installing the
RS485:3 module"
Symbols on the tab <Base Load Sequencing>
The symbols which are displayed on the tab next
to the symbol, can vary according to the base load
sequencing operating state. The following informa-
tion is displayed:
Symbol Meaning
Base Load Sequencing is switched off.
All compressors operate indepen-
dently of each other, according to their
respective settings.
Base Load Sequencing is switched on.
Base Load Sequencing is switched on
and timer-controlled.
An alarm is displayed in the "Base Load
Sequencing" menu.
Chart 10-3: Symbols on the tab <Base Load Sequenc-
ing>
Menu "Base Load Sequencing"
If the tab <Base Load Sequencing> is activated,
tapping allows the menu "Base Load Sequencing
(BLS)" to be called up.

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the CompAir DELCOS XL Series and is the answer not in the manual?

CompAir DELCOS XL Series Specifications

General IconGeneral
BrandCompAir
ModelDELCOS XL Series
CategoryController
LanguageEnglish

Related product manuals