UGE048/1103 CSC Combination Puller/Cutter
TABLE OF
CONTENTS
TROUBLESHOOTING . . . . . . . . . . . . . . . .6-1
Before Beginning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-2
A Few Words of Caution . . . . . . . . . . . . . . . . . . . . . . . . . .6-2
Identify the Cause of a Problem . . . . . . . . . . . . . . . . . . . . .6-4
Puller Operation Problems . . . . . . . . . . . . . . . . . . . . . . . . .6-5
Cutter Operation Problems . . . . . . . . . . . . . . . . . . . . . . . . .6-7
Product Quality Problems . . . . . . . . . . . . . . . . . . . . . . . .6-11
Restoring Default Memory Settings . . . . . . . . . . . . . . . . .6-16
Restoring User-Specific Memory Settings . . . . . . . . . . . .6-16
Replacing Safety and Proximity Switches . . . . . . . . . . . .6-17
Checking the Servo Amplifier . . . . . . . . . . . . . . . . . . . . .6-18
Adjusting the Proximity Switches . . . . . . . . . . . . . . . . . .6-18
Checking the Encoder . . . . . . . . . . . . . . . . . . . . . . . . . . .6-18
Checking the Motor/Reducer Assembly . . . . . . . . . . . . . .6-19
Testing Repeatability . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-20
Results of Repeatability Testing . . . . . . . . . . . . . . . . . . .6-21
APPENDIX . . . . . . . . . . . . . . . . . . . . . . . . .
Customer Service Information . . . . . . . . . . . . . . . . . . . . . .A-1
Warranty Information . . . . . . . . . . . . . . . . . . . . . . . . . . . .A-2
Cutter Blade Selection and Use . . . . . . . . . . . . . . . . . . . . .B-1
Cutting Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-3
Calculating Blade Interruption . . . . . . . . . . . . . . . . . . . . . .B-4
Conair Cutter Blades . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-6
All About Cutter Bushings . . . . . . . . . . . . . . . . . . . . . . . .C-1
Blade and Bushing Lubrication . . . . . . . . . . . . . . . . . . . . .D-1
Choosing Belt Materials . . . . . . . . . . . . . . . . . . . . . . . . . .E-1
Conair Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .E-1
Puller Control Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . .F-1
Advanced Procedure: PID Tuning . . . . . . . . . . . . . . . . . . .F-3
Using the Digital Belt Gap Sensor . . . . . . . . . . . . . . . . . .G-1
Adjusting the Pneumatic Upper Belt Actuator . . . . . . . . . .G-2
PARTS/DIAGRAMS
This section has been provided for you to
store spare parts lists and diagrams.
iii
To Next Page
Loading...