Danfoss vlt FC 102 Programming Guide

Parameter 1-10 Motor
Construction
[0]
Asynchron
[1] PM Motor
non salient
Parameter 1-14 Damping Gain x
Parameter 1-15 Low Speed Filter
Time Const.
x
Parameter 1-16 High Speed Filter
Time Const.
x
Parameter 1-17 Voltage lter time
const.
x
Parameter 1-20 Motor Power [kW] x
Parameter 1-21 Motor Power [HP] x
Parameter 1-22 Motor Voltage x
Parameter 1-23 Motor Frequency x
Parameter 1-24 Motor Current x x
Parameter 1-25 Motor Nominal
Speed
x x
Parameter 1-26 Motor Cont. Rated
Torque
x
Parameter 1-28 Motor Rotation
Check
x x
Parameter 1-29 Automatic Motor
Adaptation (AMA)
x
Parameter 1-30 Stator Resistance
(Rs)
x x
Parameter 1-31 Rotor Resistance (Rr) x
Parameter 1-35 Main Reactance (Xh) x
Parameter 1-37 d-axis Inductance
(Ld)
x
Parameter 1-39 Motor Poles x x
Parameter 1-40 Back EMF at 1000
RPM
x
Parameter 1-50 Motor Magneti-
sation at Zero Speed
x
Parameter 1-51 Min Speed Normal
Magnetising [RPM]
x
Parameter 1-52 Min Speed Normal
Magnetising [Hz]
x
Parameter 1-58 Flying Start Test
Pulses Current
x x
Parameter 1-59 Flying Start Test
Pulses Frequency
x x
Parameter 1-60 Low Speed Load
Compensation
x
Parameter 1-61 High Speed Load
Compensation
x
Parameter 1-62 Slip Compensation x
Parameter 1-63 Slip Compensation
Time Constant
x
Parameter 1-64 Resonance
Dampening
x
Parameter 1-65 Resonance
Dampening Time Constant
x
Parameter 1-66 Min. Current at Low
Speed
x
Parameter 1-70 Start Mode x
Parameter 1-10 Motor
Construction
[0]
Asynchron
[1] PM Motor
non salient
Parameter 1-71 Start Delay x x
Parameter 1-72 Start Function x x
Parameter 1-73 Flying Start x x
Parameter 1-77 Compressor Start
Max Speed [RPM]
x
Parameter 1-78 Compressor Start
Max Speed [Hz]
x
Parameter 1-79 Compressor Start
Max Time to Trip
x
Parameter 1-80 Function at Stop x x
Parameter 1-81 Min Speed for
Function at Stop [RPM]
x x
Parameter 1-82 Min Speed for
Function at Stop [Hz]
x x
Parameter 1-86 Trip Speed Low
[RPM]
x x
Parameter 1-87 Trip Speed Low [Hz] x x
Parameter 1-90 Motor Thermal
Protection
x x
Parameter 1-91 Motor External Fan x x
Parameter 1-93 Thermistor Source x x
Parameter 2-00 DC Hold/Preheat
Current
x
Parameter 2-01 DC Brake Current x x
Parameter 2-02 DC Braking Time x
Parameter 2-03 DC Brake Cut In
Speed [RPM]
x
Parameter 2-04 DC Brake Cut In
Speed [Hz]
x
Parameter 2-06 Parking Current x
Parameter 2-07 Parking Time x
Parameter 2-10 Brake Function x x
Parameter 2-11 Brake Resistor (ohm) x x
Parameter 2-12 Brake Power Limit
(kW)
x x
Parameter 2-13 Brake Power
Monitoring
x x
Parameter 2-15 Brake Check x x
Parameter 2-16 AC brake Max.
Current
x
Parameter 2-17 Over-voltage Control x
Parameter 4-10 Motor Speed
Direction
x x
Parameter 4-11 Motor Speed Low
Limit [RPM]
x x
Parameter 4-12 Motor Speed Low
Limit [Hz]
x x
Parameter 4-13 Motor Speed High
Limit [RPM]
x x
Parameter 4-14 Motor Speed High
Limit [Hz]
x x
Parameter 4-16 Torque Limit Motor
Mode
x x
Parameter Descriptions
VLT
®
HVAC Drive FC 102
50 Danfoss A/S © 10/2019 All rights reserved. M0010001
33

Danfoss vlt FC 102 Specifications

General

Brand	Danfoss
Model	vlt FC 102
Category	DC Drives
Language	English