DMC SuperSigma2 User Manual

SuperSigma2 AM PMS – V1.5.6 17-1-2020 Page 3 (97) ©2019 DMC GmbH Herten Germany
Contents
1 ABOUT THIS MANUAL ............................................................................................................................................ 9
1.1 REFERENCES .............................................................................................................................................................. 9
1.2 HOW SETTINGS ARE NUMBERED IN THIS DOCUMENT .......................................................................................................... 9
1.3 HOW TO CORRECTLY AND TIME-EFFICIENTLY SETUP A CONTROLLER........................................................................................ 9
2 CONTROL CONNECTIONS ..................................................................................................................................... 10
Pin 1 Forward i/p -- Pump Potentiometer Switch 1 .............................................................................................. 10
Pin 2 Reverse i/p -- Pump Switch 2 ....................................................................................................................... 10
Pin 3 Footswitch / Belly Button -- Pump Switch 3 ................................................................................................. 10
Pin 4 Seat / Tiller -- Pump Switch 4 ....................................................................................................................... 11
Pin 5 Speed Limit 1 / Inch Forward -- Pump Switch 5 ........................................................................................... 11
Pin 6 Speed Limit 2 / Inch Reverse -- Pump Switch 6 (Power Steer Input) ............................................................ 11
Pin 7 Speed Limit 3 / Handbrake -- Pump Inhibit .................................................................................................. 12
Pin 8 Analogue supply 5V...................................................................................................................................... 12
Pin 9 Analogue AD1 i/p Accelerator -- Potentiometer .......................................................................................... 12
Pin 10 Analogue supply 0V...................................................................................................................................... 12
Pin 11 Analogue AD2 -- Footbrake pot ................................................................................................................... 13
Pin 12 Analogue AD3 -- Steer pot ........................................................................................................................... 13
Pin 13 Key i/p .......................................................................................................................................................... 13
Pin 14 Contactor supply o/p .................................................................................................................................... 13
Pin 15 Contactor 1 o/p (Line) .................................................................................................................................. 13
Pin 16 Contactor 2 o/p (Magnet Brake - Fan control)............................................................................................. 14
Pin 17 Contactor 3 o/p (Powersteer - Fan control) ................................................................................................. 14
Pin 18 Digital o/p -- Remote LED or Brake lights or Drive OK ................................................................................. 14
Pin 19 Supply 12V -- 70mA max. ............................................................................................................................. 14
Pin 20 CAN +12V -- 70mA max. ............................................................................................................................... 14
Pin 21 CAN H1 ......................................................................................................................................................... 14
Pin 22 CAN L1 .......................................................................................................................................................... 14
Pin 23 CAN 0V ......................................................................................................................................................... 14
Pin 24 CAN 120R Link .............................................................................................................................................. 14
Pin 25 CAN H2 ......................................................................................................................................................... 15
Pin 26 CAN L2 .......................................................................................................................................................... 15
Pin 27 Sensor supply +5V / +12V ............................................................................................................................. 15
Pin 28 Hall 1 i/p ....................................................................................................................................................... 15
Pin 29 Hall 2 i/p ....................................................................................................................................................... 15
Pin 30 Hall 3 i/p ....................................................................................................................................................... 15
Pin 31 Sensor supply 0V .......................................................................................................................................... 15
Pin 32 Motor Sensor Sine ........................................................................................................................................ 15
Pin 33 Motor Sensor CoSine .................................................................................................................................... 15
Pin 34 Thermistor AD4 i/p ....................................................................................................................................... 15
Pin 35 Thermistor 0V............................................................................................................................................... 15
2.1 LIGHT WIRING OF PMS CONTROLLER ........................................................................................................................... 16
2.1.1 Connectors’ pin assignment for Traction ..................................................................................................... 16
2.1.2 Light wiring example for traction ................................................................................................................. 17
2.1.3 Connectors’ pin assignment for Pump ......................................................................................................... 18
2.1.4 Light wiring example for pump .................................................................................................................... 19
2.2 SELECTING ACTIVE LOW OR HIGH DIGITAL INPUTS ............................................................................................................ 20
2.2.1 Active Low digital inputs .............................................................................................................................. 20
2.2.2 Active High digital inputs ............................................................................................................................. 21
2.3 USE OF OHMIC POTENTIOMETERS AND ELECTRONIC POTENTIOMETERS ............................................................................... 21
2.4 POWER WIRING ....................................................................................................................................................... 22
3 MENU 1 “ADJUSTMENT” ...................................................................................................................................... 23
3.1 MENU 1 “TRACTION ADJUSTMENTS” ........................................................................................................................... 23
M1-1T Acceleration delay “Accel” ........................................................................................................................... 24
M1-2T Deceleration delay “Decel” .......................................................................................................................... 25

DMC SuperSigma2 Specifications

General

Brand	DMC
Model	SuperSigma2
Category	Engine
Language	English