Emerson Affinity - Menu 17: Building Automation Network; Menu 18: Application Menu 1; Menu 19: Application Menu 2; Menu 20: Application Menu 3

Safety
Information
Product
Information
Mechanical
Installation
Electrical
Installation
Getting
Started
Basic
parameters
Running
the motor
Optimization
SMARTCARD
operation
PC tools
Advanced
parameters
Technical
Data
Diagnostics
UL Listing
Information
212 Affinity User Guide
www.controltechniques.com Issue Number: 5
11.14.3 Fieldbus module category
Fieldbus module parameters
For information regarding Fieldbus module parameters, refer to the appropriate Solutions Module User Guide.
11.15 Menu 17: Building Automation Network
11.16 Menu 18: Application menu 1
11.17 Menu 19: Application menu 2
11.18 Menu 20: Application menu 3
All menu 20 parameters are transferred to the SMARTCARD when a 4yyy transfer is performed. See section 9.2.1 Writing to the SMARTCARD on
page 130 for more information.
Parameter
Range(
Ú) Default(Ö)
Type
17.01 ID code 0 to 599 402 RO Uni PT US
17.02 Software version 0.00 to 99.99
RO Uni NC PT
17.03 MAC/Node address 0 to 65535 1 RW Uni US
17.04 Baud rate 0 to 127
0
RW Uni US
17.05 Building Automation Network protocol 0 to 65535 RW Uni US
17.06 Received message counter 0 to 9999
RO Uni NC PT
17.07
MS/TP maximum master MAC
address
0 to 3000 127 RW Uni US
17.10 Device object identifier -19 to -32767 0 RW Bi US
17.12
Communications lost detection
timeout
-32,768 to +32,768 0
RW US
17.13 Communications loss action RW US
17.35 CRC errors
0 to 2
31
-1
RO Uni NC PT
17.38 Data format 0 to 255 0 RW Uni US
17.39 Response turn-around time 0 to 255 ms 5 RW Uni NC
17.44
Real-time clock (RTC) back-up battery
low
0 to 255
0ROUniNCPT
17.45 Communications OK flag
RO Bit
17.50
Building Automation Network error
status
RO Uni NC PT
17.51 Module software sub-version 0 to 99
RO Uni NC PT
Parameter
Range(
Ú) Default(Ö)
Type
18.01
Application menu 1 power-down
saved integer
-32,768 to +32,767
0
RW Bi NC PS
18.02 to
18.10
Application menu 1 read-only integer RO Bi NC
18.11 to
18.30
Application menu 1 read-write integer RW Bi US
18.31 to
18.50
Application menu 1 read-write bit OFF (0) or On (1) RW Bit US
Parameter
Range(
Ú) Default(Ö)
Type
19.01
Application menu 2 power-down
saved integer
-32,768 to +32,767
0
RW Bi NC PS
19.02 to
19.10
Application menu 2 read-only integer RO Bi NC
19.11 to
19.30
Application menu 2 read-write integer RW Bi US
19.31 to
19.50
Application menu 2 read-write bit OFF (0) or On (1) RW Bit US
Parameter
Range(
Ú) Default(Ö)
Type
20.01 to
20.20
Application menu 3 read-write integer -32,768 to +32,767
0
RW Bi NC
20.21 to
20.40
Application menu 3 read-write long
integer
-2
31
to 2
31
-1
RW Bi NC
RW Read / Write RO Read only Uni Unipolar Bi Bi-polar Bit Bit parameter Txt Text string
FI Filtered DE Destination NC Not copied RA Rating dependent PT Protected US User save PS Power down save