Emerson Unidrive M702 - Serial Communications Look up Table

Safety
information
Product
information
Mechanical
installation
Electrical
installation
Getting
started
Basic
parameters
Running
the motor
Optimization
NV Media Card
Operation
Onboard
PLC
Advanced
parameters
Technical
data
Diagnostics
UL listing
information
Unidrive M702 User Guide 275
Issue Number: 3
Table 13-5 Serial communications look up table
No Trip No Trip No Trip
1
Reserved 001 92 OI Snubber 198 Encoder 10
2
Over Volts 93 Inductor Too Hot 199 Destination
3
OI ac 94 - 95 Reserved 93 -95 200 Slot1 HF
4
OI Brake 96 User Prog Trip 201 Slot1 Watchdog
5
PSU 97 Data Changing 202 Slot1 Error
6
External Trip 98 Out Phase Loss 203 Slot1 Not installed
7
Over Speed 99 CAM 204 Slot1 Different
8
Inductance 100 Reset 205 Slot2 HF
9
PSU24 101 OHt Brake 206 Slot2 Watchdog
10
Th Brake Res 102 OHt Rectifier 207 Slot2 Error
11
Autotune 1 103 - 108 Reserved 103 - 108 208 Slot2 Not installed
12
Autotune 2 109 OI dc 209 Slot2 Different
13
Autotune 3 110 Undefined 210 Slot3 HF
14
Autotune 4 111 Configuration 211 Slot3 Watchdog
15
Autotune 5 112 - 167 User Trip 112 - 167 212 Slot3 Error
16
Autotune 6 168 Frequency Range 213 Slot3 Not installed
17
Autotune 7 169 Voltage Range 214 Slot3 Different
18
Autotune Stopped 170 - 173 Reserved 170 - 173 215 Option Disable
19
Brake R Too Hot 174 Card Slot 216 Slot App Menu
20
Motor Too Hot 175 Card Product 217 App Menu Changed
21
OHt Inverter 176 Name Plate 218 Temp Feedback
22
OHt Power 177 Card Boot 219 An Output Calib
23
OHt Control 178 Card Busy 220 Power Data
24
Thermistor 179 Card Data Exists 221 Stored HF
25
Th Short Circuit 180 Card Option 222 Over Frequency
26
I/O Overload 181 Card Read Only 223 Rating Mismatch
27
OHt dc bus 182 Card Error 224 Drive Size
28
An Input Loss 1 183 Card No Data 225 Current Offset
29
An Input Loss 2 184 Card Full 226 Soft Start
30
Watchdog 185 Card Access 227 Sub-array RAM
31
EEPROM Fail 186 Card Rating 228 - 247 Reserved 228 - 247
32
Phase Loss 187 Card Drive Mode 248 Derivative Image
33
Resistance 188 Card Compare 249 User Program
34
Keypad Mode 189 Encoder 1 250 Slot4 HF
35
Control Word 190 Encoder 2 251 Slot4 Watchdog
36
User Save 191 Encoder 3 252 Slot4 Error
37
Power Down Save 192 Encoder 4 253 Slot4 Not installed
38
Low Load 193 Encoder 5 254 Slot4 Different
39
Line Sync 194 Encoder 6 255 Reset Logs
40 -89
User Trip 40 - 89 195 Encoder 7
90 Power Comms 196 Encoder 8
91 User 24V 197 Encoder 9