Endress+Hauser Liquicap M FMI51 HART - Default Chapter; Table of Contents

Liquicap M FMI51 HART Table of contents
Endress+Hauser 3
Table of contents
1 About this document ................ 6
1.1 Document function ..................... 6
1.2 Document conventions ................... 6
1.2.1 Safety symbols .................. 6
1.2.2 Electrical symbols ................ 6
1.2.3 Tool symbols .................... 6
1.2.4 Symbols for
certain types of information and graphics 7
1.3 Documentation ........................ 8
1.3.1 Technical Information ............. 8
1.3.2 Certificates ..................... 8
1.4 Registered trademarks .................. 10
2 Basic safety instructions ........... 11
2.1 Requirements for the personnel ........... 11
2.2 Workplace safety ...................... 11
2.3 Operational safety ..................... 11
2.3.1 Ex-area ....................... 11
2.4 Product safety ........................ 11
3 Incoming acceptance and product
identification ..................... 12
3.1 Incoming acceptance ................... 12
3.2 Product identification ................... 12
3.3 Storage and transport .................. 12
4 Mounting ......................... 13
4.1 Quick installation guide ................. 13
4.2 Mounting requirements ................. 14
4.2.1 Mounting the sensor ............. 14
4.2.2 Support with marine approval (GL) .. 15
4.3 Measuring condition ................... 15
4.4 Minimum probe length for nonconductive
media < 1 µS/cm ...................... 16
4.5 Installation examples ................... 16
4.5.1 Rod probes .................... 16
4.6 Probe with separate housing ............. 19
4.6.1 Extension heights: separate
housing ...................... 19
4.6.2 Wall bracket ................... 21
4.6.3 Wall mounting ................. 21
4.6.4 Pipe mounting ................. 22
4.6.5 Shortening the connecting cable .... 22
4.7 Installation instructions ................. 23
4.7.1 Probe installation ............... 24
4.7.2 Aligning the housing ............. 25
4.7.3 Sealing the probe housing ......... 25
4.8 Post-installation check .................. 25
5 Electrical connection .............. 26
5.1 Connecting requirements ................ 26
5.1.1 Potential equalization ............ 26
5.1.2 Electromagnetic compatibility
(EMC) ........................ 26
5.1.3 Cable specification ............... 26
5.1.4 Connector ..................... 27
5.1.5 Supply voltage .................. 27
5.2 Wiring and connecting .................. 27
5.2.1 Connection compartment ......... 27
5.2.2 Terminal assignment ............. 29
5.2.3 Connecting HART with other supply
units ......................... 30
5.3 Post-connection check .................. 30
6 Operation options ................. 31
6.1 Overview of operation options ............ 31
6.1.1 Display and operating elements at
the FEI50H electronic insert ....... 31
6.1.2 Operation via the optional display
and operating module ............ 32
6.1.3 The operating menu ............. 34
6.2 Error messages ....................... 37
6.3 Locking and unlocking configuration ....... 37
6.3.1 Key locking .................... 37
6.3.2 Key unlocking .................. 37
6.3.3 Software locking ................ 37
6.4 Resetting to factory setting .............. 38
6.4.1 Using the reset ................. 38
6.4.2 Effects of a reset ................ 38
6.4.3 Performing a reset ............... 38
6.5 Operation via FieldCare Device Setup ....... 38
6.5.1 Function scope ................. 38
6.5.2 Source for device description files .... 38
7 Commissioning .................... 39
7.1 Installation and function check ............ 39
7.2 Basic setup without the display or operating
module ............................. 39
7.2.1 Function switch: position 1.
Operation ..................... 40
7.2.2 Function switch: position 2. Carry
out empty calibration - for empty
tanks ........................ 40
7.2.3 Function switch: position 2. Carry
out empty calibration - for almost
empty tanks ................... 40
7.2.4 Function switch: position 3. Carry
out full calibration - for full tanks .... 41
7.2.5 Function switch: position 3. Carry
out full calibration - for almost full
tanks ........................ 41
7.2.6 Function switch: position 4.
Measuring modes ............... 42
7.2.7 Function switch: position 5.
Measuring range ................ 42