Epson EMP-TW1000 - PROJECTOR DISASSEMBLY AND ASSEMBLY FLOWCHART

4-6
EMP-TW1000
SEIKO EPSON Revision:A
4.2 Projector Disassembly and Assembly
The general disassembly procedure for the EMP-TW1000 projectors is illustrated below.
Except where indicated separately, all reassembly should be carried out by following the
disassembly procedures in reverse. Detailed disassembly procedures for each component are
given in Sections 4.1.2 to 4.2.19, which links to the flowchart given below.
Figure 4-1.
(4.2.14)
(4.2.14)
(4.2.7)
(4.2.8)
(4.2.8)
(4.2.12)
(4.2.12)
(4.2.12)
(4.2.12)
(4.2.15)
(4.2.15)
(4.2.16)
(4.2.18)
(4.2.18)
(4.2.19)
(4.2.19)
(4.2.3)
(4.2.3)
(4.2.5)
(4.2.12)
(4.2.12)
(4.2.14)
(4.2.11)
(4.2.15)
(4.2.15)
(4.2.16)
(4.2.16)
(4.2.18)
(4.2.18)
(4.2.1)
(4.2.7)
(4.2.7)
(4.2.9)
(4.2.9)
(4.2.13)
(4.2.13)
(4.2.13)
(4.2.19)
(4.2.19)
(4.2.7)
(4.2.11)
(4.2.9)
(4.2.10)
(4.2.13)
(4.2.17)
(4.2.17)
(4.2.19)
(4.2.19)
(4.2.4)
(4.2.4)
(4.2.4)
(4.2.7)
(4.2.9)
(4.2.10)
(4.2.10)
(4.2.10)
(4.2.13)
(4.2.13)
(4.2.15)
(4.2.18)
(4.2.15)
(4.2.19)
(4.2.19)
(4.2.2)
(4.2.2)
(4.2.14)
(4.2.14)
(4.2.14)
(4.2.14)
(4.2.14)
(4.2.18)
(4.2.1)
(4.2.18)
(4.2.13)
Sheet, Insulation, Lamp
Shielding Gasket
PROJECTOR
Lid, Lamp Unit
Model Name Plate,
EMP-TW1000
Foot; A10 Lid, Airfilter Logo Plate; EPSON32H
Lamp Unit
Holder Foot; A Air Filter
Case, Upper; B
Rubber Foot
Focus Ring; B
Plate, Ground, MA
Plate MA Fasten Left
MA-IF Board Assy.
Plate, Shade, PS
Cable, RCR; FIF
Printed Circuit Board
Assembly; RC_R1
Cushion, Duct, Exhaust
PS Ballast Assy.
Filter, RC
Case IF
Duct, Exhaust
Plate MA Fasten Right
Plate, Lamp
LABEL, IF; A
Sheet, Shade, IF
Panel IF
Inshulock T-18S
Plate, Support, MA Fasten
Plate, MA Fasten; PS
Cushion, Shade, IF
Printed Circuit Board
Assembly; RC_R1
Printed Circuit Board
Assembly; TH_R1
Optical Engine
Plate, Fasten; A
Printed Circuit Board
Assembly; IF_R1
Cable, RCR; FIF
Cable, C; 170
Duct, Light ValveMotor CF Assy. Frame, SW, CF Auto Iris Assy.
Fan, Exhaust; B
Duct, Intake, Light Valve
Sheet, Duct, PBS
Spring, ML Fasten TOP
Frame CF Assy.
Micro SW Assy.
Duct, Intake, LMP
Sheet, Duct, Light Valve
SW CF Assy.
Plate_Ground_Lensbase; A
Fan, Intake
Duct, PS
Fan, Lamp
Cable AC
Cushion, Light Valve
Duct, Intake, PS
Fan Guard, Lamp Fan
Sheet, Duct, Ballast
Sheet, Duct, PS
Filter, RC Frame, Intake FanSheet, Heatresistant; A
Plate PS Conduction A Switch, Lamp Lid Detect
Case, Lower
Fan, Intake
Sheet, Heatresistant; B
Plate PS Conduction B
Lamp Lid Detection
Switch Plate
Cushion, Light Valve
(4.2.6)
(4.2.6)
(4.2.6)
(4.2.7)
Printed Circuit Board
Assembly; SW_R2
CABLE, SW; Au
Button, SW
Case Unit Front; F
(4.2.7)
(4.2.7)
(4.2.7)
Zoom Ring; B
Zoom Ring, Shade
Cushion, Zoom Ring
C H E C K
P O I N T
Part names indicated in the above flow and used in this chapter are simplified
names. See the “Part Names given in the SPI” table on the next page to know
their corresponding official names.