Need help?Do you have a question about the Ericsson Redback Networks SmartEdge 1200 and is the answer not in the manual?
General| Brand | Ericsson |
|---|---|
| Model | Redback Networks SmartEdge 1200 |
| Category | Network Router |
| Language | English |
States the purpose of this guide, which is to provide information for site preparation, installation, and servicing of the SmartEdge 1200 router.
Lists recommended documentation for complete and correct installation of the SmartEdge 1200 router.
Defines the target audience for this guide, assuming familiarity with general hardware installation and service procedures.
Describes the structure of the guide, outlining the content of each chapter and appendix.
Explains the document conventions used for notes, cautions, and warnings to convey special information.
Details the cross-references and other navigational elements used to aid in accessing information within the guide.
Provides information on how to order additional copies of Redback Networks documentation and provide feedback.
Provides a functional overview of the SmartEdge 1200 router, its architecture, and applications.
Lists the main system components of the SmartEdge 1200 router: Chassis, Controller Cards, and Traffic Cards.
Describes the Enhanced ATM OC-12c/STM-4c IR card, its port, and its features like SAR devices and queuing.
Details the ATM OC-3c/STM-1c IR card, its four ports, and its second-generation capabilities for VPs and PVCs.
Describes the 10/100 Ethernet and FE-GE cards, including their port counts and selectable speeds.
Lists the transceiver-based Gigabit Ethernet cards supported by SmartEdge routers.
Describes the OC-192c/STM-64c card, its single 9.9-Gbps port, and supported XFP transceiver types.
Covers planning for hardware installation, including site selection and considerations.
Guides the decision-making process for choosing management access methods for initial startup and normal operations.
Lists the required cables and tools needed for the SmartEdge 1200 hardware installation.
Provides an introduction to the hardware installation process, referencing preinstallation tasks and safety considerations.
Details the procedures for safely mounting the SmartEdge 1200 chassis in a rack, including bracket installation.
Describes how to install the removable air ramp below the chassis for proper ventilation.
Explains how to connect the chassis power cables to the power sources and fuse panel.
Provides instructions for installing the cable tray component onto the chassis.
Guides the final steps of installation, including selecting slots and installing cards and blank cards.
Covers connecting and routing various cables, including management, external timing, and traffic card cables.
Explains how to power on the SmartEdge 1200 router by inserting fuses and how to power it off by removing fuses.
Describes how to determine hardware status using system and card LEDs, and power-on diagnostics results.
Introduces CLI commands for displaying hardware status, configuration, and troubleshooting.
Provides troubleshooting directions for hardware issues, including LED interpretation and on-demand diagnostics.
Instructs users to contact technical support and lists the information needed to help diagnose problems.
Describes the general procedure for inserting and extracting alarm, controller, or traffic cards from the chassis.
Details the procedure for inserting and removing transceivers (GBIC, SFP, XFP) from Gigabit Ethernet and OC-192c/STM-64c ports.
Covers procedures for adding, replacing, or upgrading controller cards, including adding a second controller.
Describes how to install and remove CF cards from the controller card's front panel slot.
Covers procedures for adding or replacing traffic cards in the SmartEdge 1200 chassis.
Explains how to replace a transceiver without removing the Gigabit Ethernet card, but requires port shutdown.
Describes the procedure for replacing the fan tray, noting that the system can operate without fans temporarily.
Details how to replace the air filter for the chassis cooling system, recommending a replacement schedule.
Explains the importance of cleaning fiber-optic components for quality connections and provides a reference for detailed procedures.
Provides cable and connector specifications for system management ports, including console and Ethernet cables.
Details the pin assignments for the Craft console cable connecting a console to a controller card's Craft port.
Lists the pin assignments for the shielded Ethernet crossover cable connecting a PC to a controller card's Ethernet port.
Provides pin assignments for the shielded Ethernet straight cable connecting a controller card to a LAN hub.
Lists cable specifications for external timing cables connecting to BITS or SSU synchronization sources.
Describes cable specifications for ATM, 10/100 Ethernet, Fast Ethernet-Gigabit Ethernet, and SONET/SDH traffic cards.
Lists cable specifications for the transceiver-based OC-192c/STM-64c traffic card.
Lists supported alarms for the chassis and system as a whole, including severity, probable cause, and service impact.
Lists supported alarms for traffic cards, detailing severity, probable cause, and service impact.
Lists supported alarms applicable to controller cards, including severity, probable cause, and service impact.
Provides tables of alarms for optical, Ethernet, and Gigabit Ethernet ports, categorized by layer and type.
To Next Page
