Need help?Do you have a question about the eSID 3 and is the answer not in the manual?
Details compatibility with Saab 9-3 models 2007-2014, showing visual differences.
Lists supported languages and the auto-detection feature for the eSID3 interface.
Describes the required cables for connecting the eSID3 unit to the car's OBD connector.
Configurable 12V output for LEDs, relays, or other devices, controlled by eSID3 settings.
Explains icons displayed in the upper right corner of various display views.
Views with three parameters each, some unique to special views for detailed data.
Shows real-time fuel consumption in liters/100km or mpg, also per hour.
Calculates and displays average fuel consumption over distance driven.
Tracks injected fuel for the current driving cycle and total accumulated fuel.
Displays Engine Speed, Vehicle Speed, Torque, and Power simultaneously.
Shows the current actual engine performance in torque and power.
Displays the maximum measured engine performance in torque and power.
Shows the current engine coolant temperature in Celsius or Fahrenheit.
Displays current and maximum turbo boost pressure and vacuum values.
Shows the control signal percentage to the turbo wastegate actuator.
Displays the temperature of the air entering the engine.
Measures and displays the actual air mass entering the engine.
Displays the maximum measured air mass value for B207 engines.
Shows the ignition timing angle in degrees before Top Dead Center (TDC).
Monitors knock and misfire counts for B207 engines.
Monitors misfire counts for B284 engines across cylinders.
Displays the ethanol mixture percentage for BioPower cars.
Shows Lambda value and calculated Air Fuel Ratio for B284 engines.
Displays the gearbox oil temperature for automatic transmissions.
Shows temperature estimates for the XWD system's oil and clutch.
Provides status information on the Diesel Particulate Filter (DPF).
Displays fuel pressure and pump driver signal for B284 engines.
Shows the fuel rail pressure measurement for diesel engines.
Displays the engine oil pressure measurement for B284 engines.
Estimates and displays the remaining oil life percentage based on usage.
Shows Exhaust Gas Recirculation (EGR) and Swirl flap status for diesel engines.
Displays the estimated power transfer percentage to the rear wheels.
Tracks driving distance for the current cycle and total accumulated distance.
Shows driving time for the current cycle or since the last reset.
Calculates time taken for selected speed intervals or distances.
Displays tire pressure and temperature for vehicles equipped with TPMS.
Shows battery voltage drop during engine cranking, indicating battery status.
Displays the measured battery voltage of the vehicle.
Includes battery temperature, state of charge (SoC), and current.
Displays the current system date and time synchronized with the car's clock.
Reads all Diagnostic Trouble Codes (DTCs) from vehicle ECUs.
Clears all Diagnostic Trouble Codes (DTCs) from the vehicle's ECUs.
Initiates a forced Diesel Particulate Filter (DPF) regeneration cycle.
Configures up to five favorite views for quick access from the main menu.
Allows creating custom views with three parameters each from available data.
Adjusts fuel and distance readings for improved accuracy against external sources.
Configures the startup welcome message text displayed after ignition.
Configures automatic activation of front fog lights based on conditions.
Configures the number of extra turn signal blinks activated by the stalk.
Sets display units for various parameters like torque, temperature, and volume.
Configures eSID3 to start automatically after ignition, showing last active view.
Configures the user-adjustable interval wiper function parameters.
Guides on setting the system time, date, and 12/24h format.
Selects the display language for the eSID3 interface, including auto-detection.
Configures which exterior lights activate and for how long upon unlocking.
Configures automatic folding/unfolding of side mirrors based on lock/unlock actions.
Adjusts torque estimation for B207 engines based on air mass and tuner input.
Configures the run time duration for the auxiliary parking heater.
Configures the 12V digital output logic, conditions, and thresholds.
Selects the output source for the 12V digital output or extra light relay.
Adjusts the sensitivity level for the automatic hazard activation feature.
Configures the functionality of the extra light switch.
Configures a digital input switch for functions like TCS/ESP Off.
Sets the vehicle's engine type for accurate parameter display and function.
To Next Page
General