Fagor CNC 8060 - Page 147

Installation manual
CNC 8060
CNC 8065
MACHINE PARAMETERS.
2.
(REF: 1402)
·147·
Machine parameters for the axes. Work sets.
LINEAR ACCELERATION (G0 MOVEMENTS).
LACC1G0
Acceleration of the first section (G0 movements).
Parameter valid for linear and rotary axes and spindles.
Parameter valid for analog drive, Sercos and simulated.
Possible values: From 1.0000 to 1000000.0000 mm/s² or degrees/s² / from 0.03937 to 3937.00787
inch/s².
Default value: 1000.0000 mm/s² or degrees/s² / 39.37008 inch/s².
Associated variable: (V.)[ch].MPA.LACC1G0[set].xn
See parameter LACC2G0.
LACC2G0
Acceleration of the second section (G0 movements).
Parameter valid for linear and rotary axes and spindles.
Parameter valid for analog drive, Sercos and simulated.
Possible values: From 1.0000 to 1000000.0000 mm/s² or degrees/s² / from 0.03937 to 3937.00787
inch/s².
Default value: 1000.0000 mm/s² or degrees/s² / 39.37008 inch/s².
Associated variable: (V.)[ch].MPA.LACC2G0[set].xn
Parameters LACC1G0 and LACC2G0 set the acceleration values when it is linear (parameter
SLOPETYPE) or when working with HSC in FAST mode. The CNC applies parameters
LACC1G0 and LACC2G0 to G0 movements.
LFEEDG0
Acceleration changing speed (G0 movements).
Parameter valid for linear and rotary axes and spindles.
Parameter valid for analog drive, Sercos and simulated.
Possible values: From 0 to 200000.0000 mm/min or degrees/min / from 0 to 7873.992 inch/min / from
0 to 100000.0000 rpm.
Default value: 1000.0000 mm/min, degrees/min or rpm / 39.37008 inch/min.
Associated variable: (V.)[ch].MPA.LFEEDG0[set].xn
While accelerating, when reaching the feedrate defined in this parameter, it changes the
acceleration from LACC1G0 to LACC2G0. While decelerating, when reaching the feedrate
defined in this parameter, it changes the acceleration from LACC2G0 to LACC1G0.
TRAPEZOIDAL AND SQUARE SINE ACCELERATION (G0
MOVEMENTS).
ACCELG0
Acceleration (G0 movements).
Parameter valid for linear and rotary axes and spindles.
Parameter valid for analog drive, Sercos and simulated.
Possible values: From 0.001 to 100000.0000 mm/s² or degrees/s² / from 0.0003937 to 3937.00787
inch/s².
Default value: 1000.0000 mm/s² or degrees/s² / 39.37008 inch/s².
Associated variable: (V.)[ch].MPA.ACCELG0[set].xn
See machine parameter DECELG0.
DECELG0
Deceleration (G0 movements).
Parameter valid for linear and rotary axes and spindles.
Parameter valid for analog drive, Sercos and simulated.
Possible values: From 0.001 to 100000.0000 mm/s² or degrees/s² / from 0.0003937 to 3937.00787
inch/s².
Default value: 1000.0000 mm/s² or degrees/s² / 39.37008 inch/s².
Associated variable: (V.)[ch].MPA.DECELG0[set].xn
Parameters ACCEL and DECEL set the acceleration values when it is trapezoidal or square-
sine (bell shaped) (parameter SLOPETYPE). The CNC applies parameters ACCEL and