FLAMIC S.R.L. 5 Via dell’Artigianato, 36035 Marano Vicentino (Vicenza) - Italy
6
Dough sheeter SF450 - SF500 - SF600 Operation and maintenance manual (translation of original instructions) – Ed. 10/2016
Rev.02 10/2017
All rights reserved. Reproduction in whole or in part of this manual is prohibited.
1.2 INSTRUCTIONS AND GENERAL PRECAUTIONS
Flamic s.r.l. declines all liability for injury or damage to persons, animals or property caused by the failure to
comply with instructions, directions, recommendations etc. contained in this manual, and in particular the
following:
- DO NOT tamper with the machine’s safety guards and safety devices
- DO NOT remove the guards and DO NOT disable the machine’s safety devices, unless it absolutely
necessary to do so, and with the machine stationary and the power disconnected and maintained in this
condition until all the guards and safety devices have been properly replaced/re-enabled, and after having
taken all possible measures to minimize risks that may arise
- Replace the guards and re-enable the safety devices as soon as there is no longer any reason for them to be
removed/disabled
- DO NOT use the machine for purposes and/or loads other than those indicated by the manufacturer
- Carry out daily checks on the guards, safety devices and the general condition of the machine
- Clean the machine and its parts thoroughly every day
-Adopt the necessary safety measures and precautions when carrying out adjustments, cleaning,
maintenance etc. to prevent the machine or its parts from being started by others, even accidentally
- Comply with the European Directives and the laws of the country in which the machine is used regarding the
workplace. In particular (but not limited to) those relating to safety signs, food hygiene, health and safety in the
workplace, personal protective equipment and environmental protection
- Comply with the permitted limits of the operating environment and conditions: maximum relative
humidity 90%, ambient temperature min. 5°C max. 40°C, maximum altitude 1000 m a.s.l.
- The employer must provide employees with adequate information and training, including practical training,
regarding the proper and safe use of the machine.
- The operator should wear only tight-fitting clothing, without loose parts. Jackets, open shirts etc. or
jewellery (rings, bracelets, necklaces etc.) should never be worn. Long hair should be collected (e.g. in a cap)
and work clothing must also be appropriate for the hygiene requirements of the food that is handled /
processed.
- Do not allow unauthorised persons, untrained personnel, children or anyone who is not expressly
authorised to enter the room in which the machine is used or to approach the machine;
- when the machine is connected to other equipment or incorporated in a complex assembly, the manufacturer
of the assembly resulting from said connection or incorporation must carry out a risk assessment for any
additional or greater risks resulting from said operation, take appropriate measures to eliminate or minimize
the risk, comply with all the relevant requirements of the Law, Directives, Regulations etc. (including the
Directive 2006/42/EC) and declare that the assembly is compliant with them.
- If parts of the machine need to be replaced,
use only original spare parts by submitting a request to Flamic
s.r.l. Flamic s.r.l will not under any circumstances be held liable for any injuries or damage to people, animals
or property caused by the use of non-original spare parts.
- Any arbitrary modification made to the machine shall release the manufacturer from all liability for any
injuries or damage to people, animals and/or property as a result of it.
1.3 MAIN CIRCUMSTANCES IN WHICH THE COMPANY DISCLAIMS LIABILITY
Flamic s.r.l. shall not be held liable for any direct or indirect damage or injury or for the loss of production if/by:
• the machine is used for purposes other than its intended use or in ways different to those described
• installation does not conform to the manner specified in this manual
• the machine is used by insufficiency skilled personnel and, where necessary, not adequately trained for
its safe and proper use.
• inappropriate energy sources are used or that are anyway different from those indicated in this manual
and/or the enclosed documentation (e.g. wiring diagrams)
• the lack of or poor maintenance or if it is not carried out in the manner indicated herein
• the failure or partial failure to comply with the instructions provided in this manual
• the arbitrary modification of the original characteristics and equipment of the machine without having
received a formal authorization from the manufacturer.
• the connection/incorporation with/of the machine with parts and/or equipment applied or otherwise to the
machine that are not supplied, intended or authorized by Flamic s.r.l. In this case, the CE marking placed
on the machine by the manufacturer, it would no longer be valid.
To Next Page
Loading...