Questions? Please Contact Your Local Manufacturer’s Representative
SECTION 2 VTG-IOM-2016-1214 INSTALLATION
2-9
FIGURE 3 MULTIPLE VANTAGE BOILERS IN A COMMON HYDRONIC LOOP, PRIMARY ONLY VARIABLE FLOW ARRANGEMENT WITH
MOTORIZED ISOLATION VALVES RECOMMENDED
Note: Sample piping layout (P&ID) is a general representation of system installation. Good practice should be used in system design,
including but not limited to adequate pipe/valve sizing and natural ow path for system water.
DRAWING NUMBER
REV
G-31-100003
-
VANTAGE BOILER PRIMARY ONLY
VARIABLE FLOW PIPING DIAGRAM WITH
1" SIDE CLEARANCE
DESCRIPTION:
DRAWN BY:
M. BERWALD
CHECKED BY:
N/A
B.O.M. REVIEW
MECH. ENG:
N/A
ELEC. ENG:
APPROVED BY:
N/A
K.BOTTORFF
N/A
JOB NUMBER:
PROJECT NAME:
PROJECT MANAGER:
This design and
drawings are
proprietary and are the
exclusive property of
The Fulton Companies.
The corporation does
not permit their use
excep
t with prior
written consent.
The items shown in
this drawing may be
covered by one or
more patents of The
Fulton Companies.
1 OF 1
THIRD ANGLE PROJECTION
The Fulton Companies
972 Centerville Road
Pulaski, New York USA 13142
7/7/2014
7/7/2014
UNLESS OTHERWISE NOTED:
DIMENSIONS ARE IN INCHES
TOLERANCES ON
FRACTIONS
1/4
(2) PLACE DEC. .01
(3) PLACE DEC.
.005
ANGLES 2 DEG.
SURFACE FINISH
250 MICRO-INCHES
R
SHEET 1 OF 1
-
INITIAL RELEASE
--- --- --- --- ---
REVISION HISTORY
REV REVISION DESCRIPTION B.O.M. ELEC. ENG MECH. ENG CHECKED APPROVED
NOTES:
1.
2.
3.
4.
THIS IS A TYPICAL ARRANG
EMENT FOR REFERENCE PURPOSES
ONLY. ACTUAL INSTALLATI
ONS MAY REQUIRE ADDITIONAL
COMPONENTS WHICH ARE
THIS DRAWING IS NOT FO
REFER TO THE INSTALLATI
ON AND OPERATION MANUALS FOR
INFORMATION REGARDING
CLEARANCES AND INSTALLATION
REQUIREMENTS.
THE PIPING CONFIGURATI
ON SHOULD UTILIZE A REVERSE
RETURN HEADER TO PROPE
RLY BALANCE FLOW ACROSS THE
BOILERS. WHERE REVERSE
RETURN CANNOT BE USED, IT IS
RECOMMENDED TO INSTAL
L A BALANCING VALVE PER BOILER.
CONDENSATE
DRAIN TRAP
HEATING HOT
WATER RETURN
RETURN WATER
TEMPERATURE SENSOR
MOTORIZED ISOLATION VALVE
SUPPLY WATER
TEMPERATURE SENSOR
AIR REMOVAL
SYSTEM PUMP
WITH VARIABLE
SPEED DRIVE
EXPANSION TANK
HEATING HOT
WATER SUPPLY
REVERSE RETURN
(SEE NOTE 4)
FULTON VANTAGE
HYDRONIC CONDENSING
BOILERS
DRAWING NUMBER
REV
G-31-100003
-
VANTAGE BOILER PRIMARY ONLY
VARIABLE FLOW PIPING DIAGRAM WITH
1" SIDE CLEARANCE
DESCRIPTION:
DRAWN BY:
M. BERWALD
CHECKED BY:
N/A
B.O.M. REVIEW
MECH. ENG:
N/A
ELEC. ENG:
APPROVED BY:
N/A
K.BOTTORFF
N/A
JOB NUMBER:
PROJECT NAME:
PROJECT MANAGER:
This design and
drawings are
proprietary and are the
exclusive property of
The Fulton Companies.
The corporation does
not permit their use
excep
t with prior
written consent.
The items shown in
this drawing may be
covered by one or
more patents of The
Fulton Companies.
1 OF 1
THIRD ANGLE PROJECTION
The Fulton Companies
972 Centerville Road
Pulaski, New York USA 13142
7/7/2014
7/7/2014
UNLESS OTHERWISE NOTED:
DIMENSIONS ARE IN INCHES
TOLERANCES ON
FRACTIONS
1/4
(2) PLACE DEC. .01
(3) PLACE DEC.
.005
ANGLES 2 DEG.
SURFACE FINISH
250 MICRO-INCHES
R
SHEET 1 OF 1
-
INITIAL RELEASE
--- --- --- --- ---
REVISION HISTORY
REV REVISION DESCRIPTION B.O.M. ELEC. ENG MECH. ENG CHECKED APPROVED
NOTES:
1.
2.
3.
4.
THIS IS A TYPICAL ARRANGEMENT FOR REFERENCE PURPOSES
ONLY. ACTUAL INSTALLATIONS MAY REQUIRE ADDITIONAL
COMPONENTS WHICH ARE NOT SHOWN FOR CLARITY.
THIS DRAWING IS NOT FOR CONSTRUCTION PURPOSES.
REFER TO THE INSTALLATION AND OPERATION MANUALS FOR
INFORMATION REGARDING CLEARANCES AND INSTALLATION
REQUIREMENTS.
THE PIPING CONFIGURATION SHOULD UTILIZE A REVERSE
RETURN HEADER TO PROPERLY BALANCE FLOW AC
ROSS THE
BOILERS. WHERE REVERSE RETURN CANNOT BE USED, IT IS
RECOMMENDED TO INSTALL A BALANCING VALVE PER BOILER
.
CONDENSATE
DRAIN TRAP
HEATING HOT
WATER RETURN
RETURN WATER
TEMPERATURE SENSOR
MOTORIZED ISOLATION VALVE
SUPPLY WATER
TEMPERATURE SENSOR
AIR REMOVAL
SYSTEM PUMP
WITH VARIABLE
SPEED DRIVE
EXPANSION TANK
HEATING HOT
WATER SUPPLY
REVERSE RETURN
(SEE NOTE 4)
FULTON VANTAGE
HYDRONIC CONDENSING
BOILERS
To Next Page
Loading...
