Why does the media jump out on my GRAPHTEC CE6000?
If your Graphtec Plotter media jumps out to the forward side, it means you've likely selected the wrong type of media. Check the media type setting and ensure it matches the media you are using: "SHEET", "ROLL-1 REAR SET", or "ROLL-2 REAR SET."
Why does the push roller go off the media on my GRAPHTEC Plotter?
If one of the push rollers goes off the media on your Graphtec Plotter, it's likely that the leading or trailing edge of the media is not cut straight against the media. To resolve this, cut the edge of the media straight.
How to fix coarse resolution of curved lines on GRAPHTEC CE6000?
If you're experiencing coarse resolution of curved lines on your Graphtec Plotter, it could be due to the software's resolution setting being too low or the blade offset angle being too low. Try adjusting the software's resolution setting and increasing the value for the blade offset angle.
Why doesn't my GRAPHTEC CE6000 Plotter cut the specified length?
If it does not become the specified length with a slight distance error on your Graphtec Plotter, it could be due to media slipping or an incorrect distance adjust value. Try slowing down the speed, increasing the tool-up speed, and performing feeding. Additionally, perform a distance adjust.
Why does the media wobble on my GRAPHTEC CE6000 Plotter?
If the media wobbles on your Graphtec Plotter, it could be due to a couple of reasons. The push rollers might not be set correctly on the grit rollers, so check their position. Also, for the CE6000-120 model only, the hold-down force of the push roller might not be suitable for the media; in this case, use a media suitable for changing the hold-down force.
What does error E01001 mean on GRAPHTEC CE6000 Plotter?
If the Graphtec Plotter displays error code E01001 to E01005, the plotter is defective. Contact your sales representative or the Graphtec call center for assistance.
What does error E01011 mean on GRAPHTEC CE6000?
If the Graphtec Plotter displays error code E01011, the plotter is defective. Contact your sales representative or the Graphtec call center for assistance.
Why is the blade cutting into the backing sheet on my GRAPHTEC CE6000?
If the blade of your Graphtec Plotter is cutting into the backing sheet, it's likely that the blade is extended too far or the cutting FORCE is too high. Try adjusting the blade length and lowering the FORCE setting.
What to do if my GRAPHTEC Plotter displays “LOAD MEDIA!” even after setting media?
If the Graphtec Plotter displays "LOAD MEDIA!" even when the media is set and the media set lever is moved up, it could be due to a few reasons. If the media is close to transparent, the media sensor might be making false recognitions; in this case, disable the media sensor and manually set the cut area. Strong scattered reflection might also cause the media sensor to malfunction, so try repositioning the light source to avoid direct sunlight. If neither of these solutions works, there may be a defect in the operation of the media set lever sensor, and you should contact your sales representative or the Graphtec call center.
Why is my GRAPHTEC Plotter cutting on the grit roller imprint?
If your Graphtec Plotter is cutting on the grit roller imprint, it means the cutting width has been widened. To resolve this, revert the expand limit to the default setting.
General| Connectivity | USB, Serial |
|---|---|
| Cutting Force | 30-500 gf |
| Interface | USB |
| Media Types | Vinyl, film |
| Display | LCD |
| Configuration | Desktop |
| Programmable Resolution | 0.025 mm |
| Repeatability Precision | ±0.1 mm |
| Command Sets | GP-GL / HP-GL |
| Power Supply | AC 100-240 V, 50/60 Hz |
| Media Thickness | Up to 0.25 mm (0.01 in) including liner for die-cut, Up to 0.5 mm (0.02 in) for plotting |
| Operating System Compatibility | Windows |
| Number of Push Rollers | 2 |
| Pen Compatibility | Yes |
To Next Page
