260 Detail program description - Basic settings
#01
0:00h
Stop watch
Flight tim
K78
0:00.0
4.1V
0:00.0
00
0
0
0:00h
M
V
H-J Sandbrunner
Graubele
RX VOLT:4.9V
Simultaneously tapping the cd or ef selection
keys of the right touch pad (CLEAR) will reset the
inverse video fi eld back to "0".
Display light
This line determines how long the transmitter
display's backlight illumination is to remain on after
switching the transmitter on or after the last activation
of a transmitter operating element.
Available options are "unlim(ited)", "30 s", "60 s",
"120 s" and "off".
A simultaneous tap on the cd or ef selection keys
of the right touch pad (CLEAR) will reset the inverse
video fi eld to "unlimited".
Power on/off beep
A power on/off beep for the transmitter can be
switched on ("yes") and off ("no") in this line.
A simultaneous tap on the cd or ef selection keys
of the right touch pad (CLEAR) will switch this option
shown in inverse video back to "yes".
Battery type
SEL
Bottom LCD contrast 0
Battery type
Li-Io
Display light
unlim.
Power-on/off beep yes
GENERAL BASIC SETTINGS
This line specifi es whether transmitter power is
provided by a four-cell NiMH battery or a single-cell
LiPo battery. As a consequence of this setting, the
next line will offer a suitable voltage range for the
"Battery warning" threshold.
A simultaneous tap on the cd or ef selection keys
of the right touch pad (CLEAR) will switch this option
shown in inverse video back to "Lith.".
Battery warning threshold
SEL
Battery type
Li-Io
Display light
unlim.
Power-on/off beep yes
GENERAL BASIC SETTINGS
Battery warning
3.60V
You can arbitrarily specify the warning threshold for
the display …
Batt. must
be re-
charged!!
… – contingent on the battery type selection in the line
above – in increments of 0.01 volt between 4.50 and
5.50 V (NimH battery) or 3.40 and 4.20 V (LiIo/LiPo
battery). Make sure that you do not enter a value
which is too low, so that you still have suffi cient time
to safely land your model in the event of a battery
warning.
A simultaneous tap on the cd or ef selection keys
of the right touch pad (CLEAR) will switch the fi eld
shown in inverse video back to its factory setting,
4.70 V (NiMh) or 3.60 V (Lith.).
Power-on warning
SEL
Battery type
Li-Io
Power-on/off beep yes
GENERAL BASIC SETTINGS
Battery warning
3.60V
Stick warning
unlim
In this line you can determine how long the
transmitter should wait after the last actuation of an
operating element until the activation of an optical
and acoustic power-on warning before the transmitter
switches off automatically one minute later.
The values "unlim(ited)", "30 s" and 1, 5, 10, 20, 30
and 60 minutes are optional selections.
A simultaneous tap on the cd or ef selection keys
of the right touch pad (CLEAR) will reset the inverse
video fi eld to "unlimited".
Note:
To restart the transmitter after an automatic shut-off,
fi rst push the transmitter's power switch to the right
into its "OFF" position then, after about fi ve seconds,
again into its "ON" position (toward the antenna).
Touch Sense
SEL
Battery type
Li-Io
GENERAL BASIC SETTINGS
Battery warning
3.60V
Stick warning
unlim
Touch Sense
2
In this line you can select the touch sensitivity of the
touch pads in a range from 1 to 10. The lower this
number is, the more sensitive the touch pad will be to
taps and vice versa.
To Next Page
Loading...
Need help?
General
