Run the mgpstnuser codec command to configure the H.248 user codec. The H.248 user codec
will not be configured independently in this example.
Step 14 Configure the traffic profile for the IPTV service.
huawei(config)#traffic table ip index 8 cir off priority 4 priority-policy
local-setting
Step 15 Configure the VLAN translation policy and service port for the multicast service.
Configure the mapping relationship between a GEM port and an Ethernet port on the ONT. If
the ONT is connected to the STB through Ethernet port 2, map the service flow of Ethernet port
2 to GEM port 13 in the ONT line profile.
huawei(config)#ont-lineprofile gpon profile-name ftth
huawei(config-gpon-lineprofile-1)#mapping mode port
huawei(config-gpon-lineprofile-1)#gem mapping 13 1 eth 2
huawei(config-gpon-lineprofile-1)#commit
huawei(config-gpon-lineprofile-1)#quit
Configure the VLAN of the Ethernet port on the ONT. If the ONT is connected to the STB
through Ethernet port 2, add Ethernet port 2 to VLAN 1000.
huawei(config)#ont-srvprofile gpon profile-name ftth
huawei(config-gpon-srvprofile-1)#port vlan eth 2 1000
huawei(config-gpon-srvprofile-1)#multicast-forward untag
huawei(config-gpon-srvprofile-1)#commit
huawei(config-gpon-srvprofile-1)#quit
Configure the native VLAN of the ONT port. If the ONT is connected to the STB through
Ethernet port 2, the native VLAN ID is 1000.
huawei(config)#interface gpon 0/1
huawei(config-if-gpon-0/1)#ont port native-vlan 0 1 eth 2 vlan 1000
huawei(config-if-gpon-0/1)#ont port native-vlan 0 2 eth 2 vlan 1000
huawei(config-if-gpon-0/1)#quit
Create a service VLAN and add an upstream port to it. Add upstream port 0/19/0 to VLAN 1000.
huawei(config)#vlan 1000 smart
huawei(config)#port vlan 1000 0/19 0
Create service flows. Set the service VLAN to 1000, GEM port ID to 13, and user VLAN to
untagged, and use traffic profile 8.
huawei(config)#service-port 1 vlan 1000 gpon 0/1/0 ont 1 gemport 13 multi-service
user-vlan untagged rx-cttr 8 tx-cttr 8
huawei(config)#service-port 2 vlan 1000 gpon 0/1/0 ont 2 gemport 13 multi-service
user-vlan untagged rx-cttr 8 tx-cttr 8
Step 16 Create an MVLAN and configure the IGMP version.
Set the IGMP version for the MVLAN to IGMP IPv6 v2.
huawei(config)#multicast-vlan 1000
huawei(config-mvlan1000)#igmp ipv6 version v2
This operation will delete all IPv6 programs with source IP addresses in the
current multicast VLAN
Are you sure to change current IGMP IPv6 version? (y/n)[n]:y
Command is being executed. Please wait...
Command has been executed successfully
Step 17 Configure a program library.
Set the mode for obtaining multicast programs to dynamic.
SmartAX MA5600T/MA5603T/MA5608T Multi-service
Access Module
Commissioning and Configuration Guide
19 IPv6 Configuration
Issue 01 (2014-04-30) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
1932
To Next Page
Loading...
Need help?
General
