NOTE
You can set the mode for obtaining multicast programs to dynamic only when the IGMP mode is off.
huawei(config-mvlan1000)#igmp ipv6 mode off
Are you sure to close IGMP IPv6? (y/n)[n]:y
Command is being executed. Please wait...
Command has been executed successfully
huawei(config-mvlan1000)#igmp ipv6 match mode disable
Command has been executed successfully
(Optional) Set the address range for the dynamic programs. If you need to limit the address range
of dynamic programs, perform this operation. For example, set the address range of dynamic
programs to ff15::-ff15::ffff.
huawei(config-mvlan1000)#igmp ipv6 match group ipv6 ff15:: to-ipv6 ff15::ffff
Step 18 Set the IGMP IPv6 mode.
Select the IGMP IPv6 proxy mode.
huawei(config-mvlan1000)#igmp ipv6 mode proxy
Are you sure to change IGMP IPv6 mode? (y/n)[n]:y
Command is being executed. Please wait...
Command has been executed successfully
Step 19 Configure the IGMP upstream port.
Set the IGMP upstream port ID to 0/19/0 and working mode to default. Protocol packets are
transmitted to all the IGMP upstream ports in the multicast VLAN.
huawei(config-mvlan1000)#igmp uplink-port 0/19/0
huawei(config-mvlan1000)#btv
huawei(config-btv)#igmp uplink-port-mode default
Are you sure to change the uplink port mode?(y/n)[n]:y
Step 20 Configure multicast users.
Add service ports 1 and 2 as multicast users.
huawei(config-btv)#igmp policy service-port 1 normal
huawei(config-btv)#igmp policy service-port 2 normal
huawei(config-btv)#igmp user add service-port 1
huawei(config-btv)#igmp user add service-port 2
huawei(config-btv)#multicast-vlan 1000
huawei(config-mvlan1000)#igmp multicast-vlan member service-port 1
huawei(config-mvlan1000)#igmp multicast-vlan member service-port 2
huawei(config-mvlan1000)#quit
Step 21 Configure the traffic profile for the VoD service.
huawei(config)#traffic table ip index 8 cir off priority 4 priority-policy
local-setting
Step 22 Configure the VLAN translation policy and service port for the VoD service.
Configure the mapping relationship between a GEM port and a VLAN. The service flow of user
VLAN 1100 is mapped to GEM port 13 in the ONT line profile.
huawei(config)#ont-lineprofile gpon profile-name ftth
huawei(config-gpon-lineprofile-1)#gem mapping 13 4 vlan 1100
huawei(config-gpon-lineprofile-1)#commit
huawei(config-gpon-lineprofile-1)#quit
Configure the VLAN of the Ethernet port on the ONT. If the ONT is connected to the STB
through Ethernet port 2, add Ethernet port 2 to VLAN 1100.
huawei(config)#ont-srvprofile gpon profile-name ftth
huawei(config-gpon-srvprofile-1)#port vlan eth 2 1100
SmartAX MA5600T/MA5603T/MA5608T Multi-service
Access Module
Commissioning and Configuration Guide
19 IPv6 Configuration
Issue 01 (2014-04-30) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
1933
To Next Page
Loading...
Need help?
General
