IBM System x3550 M3 Type 4254 Problem Determination And Service Guide

Table 6. IMM error messages (continued)
v Follow the suggested actions in the order in which they are listed in the Action column until the problem
is solved.
v See Chapter 4, “Parts listing, System x3550 M3 Types 4254 and 7944,” on page 159 to determine which
components are customer replaceable units (CRU) and which components are field replaceable units
(FRU).
v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a
trained service technician.
Certificate Authority %1 has detected a
%2 Certificate Error.
(%1 = IBM_CertificateAuthority.
CADistinguishedName; %2 =
CIM_PublicKeyCertificate.
ElementName)
Error A problem has occurred
with the SSL Server, SSL
Client, or SSL Trusted CA
certificate that has been
imported into the IMM. The
imported certificate must
contain a public key that
corresponds to the key pair
that was previously
generated by the Generate
a New Key and
Certificate Signing
Request link.
1. Make sure that the
certificate that you are
importing is correct.
2. Try importing the
certificate again.
Ethernet Data Rate modified from %1 to
%2 by user %3.
(%1 = CIM_EthernetPort.Speed; %2 =
CIM_EthernetPort.Speed; %3 = user ID)
Info A user has modified the
Ethernet port data rate.
No action; information only.
Ethernet Duplex setting modified from
%1 to %2 by user %3.
(%1 = CIM_EthernetPort.FullDuplex; %2
= CIM_EthernetPort.FullDuplex; %3 =
user ID)
Info A user has modified the
Ethernet port duplex
setting.
No action; information only.
Ethernet MTU setting modified from %1
to %2 by user %3.
(%1 = CIM_EthernetPort.
ActiveMaximumTransmissionUnit;
%2 = CIM_EthernetPort.
ActiveMaximumTransmissionUnit;
%3 = user ID)
Info A user has modified the
Ethernet port MTU setting.
No action; information only.
Ethernet Duplex setting modified from
%1 to %2 by user %3.
(%1 =
CIM_EthernetPort.NetworkAddresses;
%2 =
CIM_EthernetPort.NetworkAddresses;
%3 = user ID)
Info A user has modified the
Ethernet port MAC address
setting.
No action; information only.
Ethernet interface %1 by user %2.
(%1 = CIM_EthernetPort.EnabledState;
%2 = user ID)
Info A user has enabled or
disabled the Ethernet
interface.
No action; information only.
Hostname set to %1 by user %2.
(%1 =
CIM_DNSProtocolEndpoint.Hostname;
%2 = user ID)
Info A user has modified the
host name of the IMM.
No action; information only.
74 IBM System x3550 M3 Types 4254 and 7944: Problem Determination and Service Guide

IBM System x3550 M3 Type 4254 Specifications

General

Processor	Intel Xeon 5600 series
Max Processors	2
Memory	Up to 192 GB DDR3
Form Factor	1U Rack
Chipset	Intel 5520
Drive Bays	Up to 4 hot-swap 2.5-inch SAS/SATA or SSD
RAID Support	RAID 0, 1, 10
Network Interface	Dual-port Gigabit Ethernet
Power Supply	460W or 675W
Expansion Slots	2 PCIe 2.0
Weight	Approximately 17.24 kg (38 lbs)
Memory Slots	18 (RDIMM) or 12 (UDIMM)