Icom IC-9100 - Editing a Repeater List; Duplex Direction Setting (DUP); Frequency Offset Programming (Offset);Storing the Repeater List; Repeater List Selection;Repeater Data Programming

91
7
DV MODE PROGRAMMING
$UPLEXDIRECTIONSETTING$508.
This content appears when “9%3” is selected in “R1
USE” as described in ‘Access repeater setting (R1
USE)’ on page 90.
#1 Push [Z](F-2) to display the “DUP” item (Duplex di-
rection setting).
s4HEDUPLEXDIRECTIONSETTINGSCREENISDISPLAYED
RP–L
DUP :  OFF

#2 Rotate [MAIN DIAL] to select the duplex direction.
s OFF : The duplex function is OFF.
s DUP– : The transmit frequency shifts down from the re-
ceive frequency by the offset amount.
s DUP+ : The transmit frequency shifts up from the re-
ceive frequency by the offset amount.
&REQUENCYOFFSETPROGRAMMING/&&3%49.
This content appears when “9%3” is selected in “R1
USE” as described in ‘Access repeater setting (R1
USE)’ on page 90.
#3 Push [Z](F-2) to display the “OFFSET” item (Fre-
quency offset Programming).
s&REQUENCYOFFSETPROGRAMMINGSCREENISDISPLAYED
RP–L
OFFSET:  0.000.0
 CLR
#4 Rotate [MAIN DIAL] to select the frequency offset.
s(OLD DOWN;#,2=& FORSECONDTOCLEARTHE DIS-
played frequency offset.
3TORINGTHEREPEATERLIST!$$710. RITE
#5 Push [Z](F-2) to display the “ADD Write” item (Re-
peater list Storing).
RP–L
ADD Write
Ú WRÙ
#6 Hold down [WR](F-5) to store the entry.
sh!$$7RITE/+vAPPEARS
RP–L
ADD Write OK?
Ú YES NOÙ
#7 Hold down ;9%3=&TOSTORETHEENTRYANDRETURN
to the RP-L screen.
N%DITINGAREPEATERLIST
This function re-programs a repeater’s data. This is
useful when already-programmed data is incorrect or
some data should be added to the list.
2EPEATERLISTSELECTION1.
q Push [DVsDR] to select the DV mode.
w
P ush [MENU] one or more times to display the “M3”
screen (Menu 3).
CS CD R>CS UR DSET
M3
e Push [DSET](F-5) to display the “DSET” screen.
DSET
TXM RP — L SET
r Push [RP-L](F-4) to display the “RP-L” screen (Re-
peater list).
RP–L
Repeater List
CLR ADD EDT
t P ush [EDT](F-5) to display the repeater list.
RP–L
 HAMACH43 GRP1
SEL
SEL GRPEDT
y Rotate [MAIN DIAL] to select the desired repeater
to be changed.
RP–L
 KOUTOU43 GRP1
SEL
SEL GRPEDT
sHold down [GRP](F-5) for 1 second to enter the
repeater group selection mode. (“≈” moves next
to the repeater group name, and then blinks.)
Rotate [MAIN DIAL] to select the desired group (0
to 9), then push [GRP](F-5).
Or, you can select the repeater group using the
keypad key.
s“SEL” appears when “R1 USE” setting is set to
“9%3” The selected repeaters can be used as an
access repeater (R1) in the DR mode, and are
scanned during an access repeater scan.
9OUCANSETTHEh3%,vSETTINGBYPUSHING[SEL](F-4).
2EPEATERDATAPROGRAMMING2.
u Push [EDT](F-1) to enter the repeater data pro-
gramming mode.
i Push [Y](F-1) or [Z](F-2) to select the item to be
changed.
o Program the selected item data. See pages 89–91
for new repeater list programming details.
RP–L
NAME: KOUTOU43
Ú EDTÙ
./4% If you are reprogramming a repeater with its
own gateway, you must also edit the gateway re-
peater call sign.
N Repeater list programming (Continued)