54
4
RECEIVE AND TRANSMIT
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
D Keyer Set mode
This Set mode is used to set the CW sidetone, mem-
ory keyer repeat time, dash weight, paddle speci๏ฌca-
tions, keyer type, etc.
s๎3ETTING๎CONTENTS
q
In the CW mode, p
ush [MENU] to display the โM1โ
screen (Menu 1).
w๎๎0USH๎;+%9=๎&๎๎๎๎TO๎DISPLAY๎THE๎h+%9v๎SCREEN๎๎-EM-
ory Keyer).
e Push [SET](F-5) to enter the Keyer Set mode.
r Push [Y](F-1) or [Z](F-2) to select the desired
item.
t Rotate [MAIN DIAL] to select the desired option.
๎s๎๎(OLD๎DOWN๎;&๎๎=๎FOR๎๎๎SECOND๎TO๎RESET๎TO๎THE๎DEFAULT๎SET-
ting, if desired.
y๎๎0USH๎ ;-%.5=๎ TO๎ SAVE๎๎ AND๎ RETURN๎ TO๎ THE๎ h+%9v๎
screen (Memory Keyer).
u
Push [MENU] to return to the โM1โ screen (Menu 1).
3IDE๎4ONE๎,EVEL๎1. ๎$EFAULT๎๎๎๎๎
๎
Select the CW sidetone output level.
s๎๎๎TO๎๎๎๎๎
๎IN๎๎๎
๎STEPS๎CAN๎BE๎SELECTED๎
3IDE๎4ONE๎,๎,IMIT๎2. ๎$EFAULT๎๎/.๎
Set the CW sidetone level limit. When the [AF] con-
trol is rotated above a speci๏ฌed level, the CW sidetone
does not increase.
s๎/.๎ ๎๎#7๎SIDETONE๎LEVEL๎IS๎LIMITED๎
s๎/&&๎๎๎#7๎SIDETONE๎LEVEL๎IS๎NOT๎LIMITED๎
Keyer 3. 2EPEAT๎4IME ๎$EFAULT๎๎๎S๎
When sending CW using the repeat timer, set the time
between transmission.
s๎๎๎TO๎๎๎๎SECONDS๎IN๎๎๎SECOND๎STEPS๎CAN๎BE๎SELECTED๎
-ESSAGE๎$ISPLAY4. ๎$EFAULT๎๎.ORMAL๎
When you are in the โSENDโ screen (Keyer Send),
channel numbers are displayed above the function
keys. However, you can display the ๏ฌrst three char-
acters of the keyer message instead of the channel
number.
Select whether to display the channel number or the
๏ฌrst three characters of the keyer.
s๎.ORMAL๎ ๎๎$ISPLAYS๎THE๎CHANNEL๎NUMBER๎
s๎-ESSAGE๎๎๎๎$ISPLAYS๎THE๎lRST๎THREE๎CHARACTERS๎OF๎THE๎
keyer message.
$OT๎$ASH๎2ATIO5. ๎$EFAULT๎๎๎๎๎๎๎๎๎๎
Set the dot/dash ratio.
s๎๎๎๎๎๎๎๎๎TO๎๎๎๎๎๎๎๎๎๎IN๎๎๎๎๎STEPS๎๎CAN๎BE๎SELECTED๎
+EYING๎WEIGHT๎EXAMPLE๎๎Morse code โKโ
To Next Page
Loading...
