Icom IC-9100 - Page 8

vii
TABLE OF CONTENTS
N Calling a specific station ................................ 103
D Confirming the setting ............................... 105
D Settings for “UR” and “R2,” depending on the
communication form .................................. 105
N Simplex operation using the VFO .................. 106
D Making a simplex CQ call or a call to
an individual station .................................. 106
N Repeater operation using the VFO ................ 107
D Making a CQ call or a call to an individual
station through your local area (access)
repeater (Local Area call) .......................... 107
D Making a CQ call or a call to an individual
station through a link repeater in the same
zone (Zone call) ........................................ 108
D Making a CQ call or a call to an individual
station through gateway repeaters
(Gateway call) ........................................... 109
D Settings for “UR” and “R2,” depending on the
communication form .................................. 110
N Message operation ........................................ 111
D TX message programming ........................ 111
D Message Transmission .............................. 112
D RX message display ................................. 112
N DV automatic detection ................................. 113
N Automatic Reply function............................... 113
N Digital squelch functions ............................... 114
N EMR communication ..................................... 115
D Adjusting the EMR AF level ...................... 115
N BK mode communication .............................. 116
N Low-speed data communication.................... 117
D Connection ................................................ 117
D Low-speed data communication application
setting ....................................................... 117
D Low-speed data communication operation . 117
N Packet loss indication .................................... 117
N DV Set mode description ............................... 118
D DV Set mode settings ............................... 118
9 GPS/GPS-A OPERATION ........................ 121–137
N GPS operation ............................................... 121
D GPS screen construction .......................... 121
D GPS data communication ......................... 122
D Sentence formatter setting ........................ 122
D Position display ......................................... 123
D
Saving your own or received position data . 124
D Display the Grid Locator information ......... 124
D GPS automatic transmission ..................... 124
D GPS message programming ..................... 125
D Received GPS message display ............... 126
N GPS memory operation ................................. 127
D Add a GPS memory .................................. 127
D Edit a GPS memory .................................. 129
D GPS alarm setting ..................................... 130
D GPS memory clearing ............................... 131
N GPS Set mode .............................................. 132
N GPS-A operation ........................................... 137
D GPS-A function ......................................... 137
D GPS-A code details ................................... 137
10 MEMORY OPERATION ............................ 138–144
N General description ....................................... 138
D Memory channel contents ......................... 138
N Memory channel selection ............................ 139
D Selection in the VFO mode ....................... 139
D Selection in the Memory mode ................. 139
NCall channel selection ................................... 139
N Memory channel programming ..................... 140
D Programming in the VFO mode ................ 140
D Programming in the Memory mode ........... 140
NCall channel programming ............................ 141
N Memory clearing ........................................... 141
N Memory contents copying ............................. 142
D Copying in the VFO mode ......................... 142
D Copying in the Memory mode ................... 142
NMemory name programming ......................... 143
NMemo pad function ........................................ 144
D Writing the displayed data into memo pads . 144
D Calling up the memo pads ........................ 144
11 SCANS ..................................................... 145–152
N Scan types .................................................... 145
N Preparation .................................................... 146
N Voice Squelch Control function ..................... 146
N Scan set mode .............................................. 147
NScan edges programming ............................. 148
N Programmed scan/Fine programmed scan
(VFO mode) .................................................. 149
D About the Fine programmed scan ............. 149
N Memory scan (Memory mode) ...................... 150
D Memory scan ............................................ 150
D Mode Select scan ..................................... 150
D
Setting/Cancelling Select Memory channels . 151
D Select Memory scan ................................. 151
N ∂F scan and Fine ∂F scan ........................... 152
D About the Fine ∂F scan ............................ 152