Integra DTR-20.1 User Manual

91
Troubleshooting—Continued
Reception is noisy, stereo FM reception suffers
from hiss, or the FM STEREO indicator doesn’t
light up
• Relocate your antenna.
• Move the AV receiver away from your TV or
computer.
• When listening to an AM station, operating the remote
controller may cause noise.
• Passing cars and airplanes can cause interference.
• Concrete walls weaken radio signals.
• If nothing improves the reception, install an outdoor
antenna.
The remote controller doesn’t work
• Make sure that the batteries are installed with the
correct polarity (page 14).
• Make sure that the remote controller is not too far
away from the AV receiver and there’s no obstruction
between the remote controller and the AV receiver’s
remote control sensor (page 14).
• Make sure you’ve selected the correct remote
controller mode (pages 13 and 82-88).
• Make sure you’ve entered the correct remote control
code (page 80).
Can’t control other components
• Make sure you’ve selected the correct remote
controller mode (pages 13 and 82-88).
• If you’ve connected an u-capable Onkyo RI Dock to
the TV/TAPE IN, GAME IN or VCR/DVR IN jacks,
for the remote controller to work properly, you must
set the Input Display to “DOCK” (see page 41).
• The entered remote control code may not be correct. If
more than one code is listed, try each one.
• With some AV components, certain buttons may not
work as expected, and some may not work at all.
• To control an Integra/Onkyo component that’s
connected via u, point the remote controller at the
AV receiver. Be sure to enter the appropriate remote
control code first (page 81).
• To control an Integra/Onkyo component that’s not
connected via u, or another manufacturer’s
component, point the remote controller at that
component. Be sure to enter the appropriate remote
control code first (page 80).
There’s no sound
• Make sure your iPod is actually playing.
• Make sure your iPod is inserted properly in the Dock.
• Make sure the UP-A1 series Dock is connected to the
UNIVERSAL PORT jacks on the AV receiver.
• Make sure the AV receiver is turned on, the correct
input source is selected, and the volume is turned up.
• Make sure the plugs are pushed in all the way.
• Try resetting your iPod.
There’s no video
• Make sure that your iPod’s TV OUT setting is set to
On.
• Make sure the correct input is selected on your TV or
the AV receiver.
• Some versions of the iPod do not output video.
The AV receiver’s remote controller doesn’t
control your iPod
• Make sure your iPod is properly inserted in the Dock.
If your iPod is in a case, it may not connect properly
to the Dock. Always remove your iPod from the case
before inserting it into the Dock.
• The iPod cannot be operated while it’s displaying the
Apple logo.
• Make sure you’ve selected the right remote mode.
• When you use the AV receiver’s remote controller,
point it toward your amp.
• If you still can’t control your iPod, start playback by
pressing your iPod’s Play button. Remote operation
should then be possible.
• Try resetting your iPod.
• Depending on your iPod, some buttons may not work
as expected.
The AV receiver unexpectedly selects your iPod
as the input source
• Always pause iPod playback before selecting a
different input source. If playback is not paused, the
Direct Change function may select your iPod as the
input source by mistake during the transition between
tracks.
Can’t record
• On your recorder, make sure the correct input is
selected.
• To prevent signal loops and damage to the AV
receiver, input signals are not fed through to outputs
with the same name (e.g., TV/TAPE IN to TV/TAPE
OUT or VCR/DVR IN to VCR/DVR OUT).
Tuner
Remote Controller
Dock for iPod
Recording
DTR-20.1_En_A.book Page 91 Wednesday, April 8, 2009 10:06 PM

Integra DTR-20.1 Specifications

General

Brand	Integra
Model	DTR-20.1
Category	Receiver
Language	English