ISHIDA WM-NANO - Installation Precautions; Unsuitable Installation Environments

Introduction
2.4 ADJUST Mode.............................................................................................. 2-25
2.4.1 Switching to Service Mode ................................................................... 2-25
2.4.2 MEMORY CLEAR Items Added............................................................ 2-25
2.4.3 SUB Tab Added to DOWN LOAD......................................................... 2-26
2.4.4 WRAPPER Added to Menu .................................................................. 2-28
2.4.5 UNIT TEST Added to Menu.................................................................. 2-30
2.4.6 WM-NANO Added to MODEL............................................................... 2-31
Chapter 3 Hardware (Mechanical).......................................................................3-1
3.1 Removing Units............................................................................................. 3-1
3.1.1 Removing the Infeed Unit ....................................................................... 3-1
3.1.2 Removing the Wrapping Unit.................................................................. 3-6
3.1.3 Dividing the Film Conveying Unit into Two ........................................... 3-16
3.1.4 Points for Unit Assembly....................................................................... 3-28
3.2 Adjustment................................................................................................... 3-29
3.2.1 Adjusting Clamp Position...................................................................... 3-29
3.2.2 Adjusting Lift Height.............................................................................. 3-33
3.2.3 Adjusting the Film Arm.......................................................................... 3-36
3.2.4 Adjusting the Mini-keeper ..................................................................... 3-46
3.2.5 Adjusting the Operating Range of the Infeed Unit’s Claw..................... 3-47
3.2.6 Adjusting Cutter Solenoid Position........................................................ 3-49
3.2.7 Adjusting Cutter Blade Position ............................................................ 3-50
3.2.8 Adjusting Left and Right Squeezing Plates Widening Amount.............. 3-51
3.2.9 Adjusting Squeeze Amount of the Postsqueezing Plate....................... 3-52
3.2.10 Adjusting Discharge Pusher Standby Position...................................... 3-53
3.2.11 Adjusting Tray Holder Height................................................................ 3-54
3.2.12 Adjusting Claw Height of the Infeed Unit .............................................. 3-55
Chapter 4 Hardware (Electrical)..........................................................................4-1
4.1 Electrical Unit Board Configuration ............................................................ 4-1
4.1.1 Alignment of Each Control Unit............................................................... 4-1
4.1.2 Front Weighing Unit................................................................................ 4-2
4.1.3 Wrapping Control Unit (1/2).................................................................... 4-3
4.1.4 Wrapping Control Unit (2/2).................................................................... 4-4
Chapter 5 Troubleshooting .................................................................................5-1
5.1 Operation as IP (Scale and Printer) ............................................................. 5-1
5.2 Error Messages ............................................................................................. 5-2
5.2.1 Error Display........................................................................................... 5-2
5.3 Error List ........................................................................................................ 5-3
5.3.1 Error relates to System (Code 100s) ...................................................... 5-3
5.3.2 Error relates to Memory (Code 200s) ..................................................... 5-5
5.3.3 Error relates to checking (Code 300s) .................................................. 5-10
5.3.4 Printers (No. 700s to 900s, 1600s, and 1800s) .................................... 5-14
5.3.5 Error relates to wrapper (Code 500s) ................................................... 5-25
5.3.6 Error related to printer (Code 700s)...................................................... 5-25
5.3.7 Error related to scale (Code 1600s)...................................................... 5-28
Appendix 1 Periodic Replacement Parts...............................................................1
Appendix 2 Wrapping by WM-NANO .....................................................................1
2.1 Part Names .........................................................................................................1
2.2 Wrapping Operation ............................................................................................2
Appendix 3 Electric Wiring Diagram......................................................................1
（5）