Jungheinrich EKS 110 User Manual

03.09 EN
76
2 Maintenance Safety Regulations
Maintenance personnel
The truck should only be serviced and repaired by the manufacturer's specialist cus-
tomer service personnel who have been trained to do this. We therefore recommend
that you enter into a maintenance contract with the manufacturer’s local sales office.
Lifting and jacking up
WARNING!
Lifting and jacking up the truck safely
In order to raise the truck, the lifting gear must only be secured to the points specially
provided for this purpose.
You may only work under a raised load handler / raised cab if they have been secured
with a sufficiently strong chain or the fastening bolt.
In order to raise and jack up the truck safely, proceed as follows:
XJack up the truck only on a level surface and prevent it from moving accidentally.
XOnly use a jack with sufficient capacity. When jacking up the truck, take appropriate
measures to prevent it from slipping or tipping over (e.g. wedges, wooden blocks).
XIn order to raise the truck, the lifting gear must only be secured to the points spe-
cially provided for this purpose. (see "Labels and Decals" on page 17).
XWhen jacking up the truck, take appropriate measures to prevent it from slipping or
tipping over (e.g. wedges, wooden blocks).
Cleaning
CAUTION!
Fire hazard!
Do not use flammable liquids to clean the industrial truck.
XAlways disconnect the battery before starting cleaning work.
XCarry out all necessary safety measures to prevent sparking before cleaning (e.g.
by short-circuiting).
CAUTION!
Risk of electrical system damage
The electrical system can be damaged if it is cleaning with water. It is prohibited to
clean the electrical system with water.
XDo not clean the electrical system with water.
XClean the electrical system with weak suction or compressed air (use a compressor
with a water trap) and not a conductive, anti-static brush.
CAUTION!
Risk of component damage when cleaning the truck
If the truck is to be cleaned with a water jet or a high-pressure cleaner, all electrical
and electronic components must be carefully covered beforehand as moisture can
03.09 EN
76
2 Maintenance Safety Regulations
Maintenance personnel
The truck should only be serviced and repaired by the manufacturer's specialist cus-
tomer service personnel who have been trained to do this. We therefore recommend
that you enter into a maintenance contract with the manufacturer’s local sales office.
Lifting and jacking up
WARNING!
Lifting and jacking up the truck safely
In order to raise the truck, the lifting gear must only be secured to the points specially
provided for this purpose.
You may only work under a raised load handler / raised cab if they have been secured
with a sufficiently strong chain or the fastening bolt.
In order to raise and jack up the truck safely, proceed as follows:
XJack up the truck only on a level surface and prevent it from moving accidentally.
XOnly use a jack with sufficient capacity. When jacking up the truck, take appropriate
measures to prevent it from slipping or tipping over (e.g. wedges, wooden blocks).
XIn order to raise the truck, the lifting gear must only be secured to the points spe-
cially provided for this purpose. (see "Labels and Decals" on page 17).
XWhen jacking up the truck, take appropriate measures to prevent it from slipping or
tipping over (e.g. wedges, wooden blocks).
Cleaning
CAUTION!
Fire hazard!
Do not use flammable liquids to clean the industrial truck.
XAlways disconnect the battery before starting cleaning work.
XCarry out all necessary safety measures to prevent sparking before cleaning (e.g.
by short-circuiting).
CAUTION!
Risk of electrical system damage
The electrical system can be damaged if it is cleaning with water. It is prohibited to
clean the electrical system with water.
XDo not clean the electrical system with water.
XClean the electrical system with weak suction or compressed air (use a compressor
with a water trap) and not a conductive, anti-static brush.
CAUTION!
Risk of component damage when cleaning the truck
If the truck is to be cleaned with a water jet or a high-pressure cleaner, all electrical
and electronic components must be carefully covered beforehand as moisture can

Jungheinrich EKS 110 Specifications

General

Brand	Jungheinrich
Model	EKS 110
Category	Trucks
Language	English