Juniper EX3300 Hardware Guide

NOTE:
•
Member links of 50-Gigabit Ethernet can only be configured using the
50-Gigabit Ethernet interfaces of 100-Gigabit Ethernet PIC with CFP
(PD-1CE-CFP-FPC4).
•
Starting with Junos OS Release 13.2, 100-Gigabit Ethernet member links
can be configured using the two 50-Gigabit Ethernet interfaces of
100-Gigabit Ethernet PIC with CFP. This 100-Gigabit Ethernet member link
can be included in an aggregated Ethernet link that includes member links
of other interfaces as well. In releases before Junos OS Release 13.2, the
100-Gigabit Ethernet member link configured using the two 50-Gigabit
Ethernet interfaces of 100-Gigabit Ethernet PIC with CFP cannot be included
in an aggregated Ethernet link that includes member links of other
interfaces.
To configure member links of mixed rates and mixed modes on T640, T1600, T4000,
and TX Matrix Plus routers, you need to configure the mixed option for the [edit interfaces
aex aggregated-ether-options link-speed] statement.
To set the required link speed:
1. Specify that you want to configure the aggregated Ethernet options.
user@host# edit interfaces interface-name aggregated-ether-options
2. Configure the link speed.
[edit interfaces interface-name aggregated-ether-options ]
user@host# set link-speed speed
speed can be in bits per second either as a complete decimal number or as a decimal
number followed by the abbreviation k (1000), m (1,000,000), or g (1,000,000,000).
Aggregated Ethernet interfaces on the M120 router can have one of the following
speeds:
•
100m—Links are 100 Mbps.
•
10g—Links are 10 Gbps.
•
1g—Links are 1 Gbps.
•
oc192—Links are OC192 or STM64c.
Aggregated Ethernet links on EX Series switches can be configured to operate at one
of the following speeds:
•
10m—Links are 10 Mbps.
•
100m—Links are 100 Mbps.
•
1g—Links are 1 Gbps.
•
10g—Links are 10 Gbps.
•
50g—Links are 50 Gbps.
91Copyright © 2015, Juniper Networks, Inc.
Chapter 2: Configuration Tasks

Juniper EX3300 Specifications

General

Ethernet LAN	Yes
Authentication method	RADIUS, TACACS+
Connectivity technology	Wired
Ethernet interface type	Gigabit Ethernet
Number of VLANs	4096
Networking standards	IEEE 802.1ab, IEEE 802.1D, IEEE 802.1Q, IEEE 802.1s, IEEE 802.1w, IEEE 802.1x, IEEE 802.3, IEEE 802.3ab, IEEE 802.3ad, IEEE 802.3x, IEEE 802.3z
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Copper ethernet cabling technology	1000BASE-T, 100BASE-TX, 10BASE-T
Console port	-
ExpressCard slot	No
Fiber ports quantity	4
USB 2.0 ports quantity	0
Basic switching RJ-45 Ethernet ports quantity	48
Throughput	130 Mpps
Number of queues	8
MAC address table	16000 entries
Maximum data transfer rate	176 Gbit/s
Supported data transfer rates	10, 100, 1000Mbps
Switch type	Managed
Switch layer	L2
Security algorithms	SSH-2
Power source	AC
AC input voltage	100 - 240 V
Power consumption (typical)	100 W
Form factor	1U
Product color	Black
Flash memory	1024 MB
Processor frequency	1000 MHz
Compatible operating systems	Junos
Operating altitude	0 - 3049 m
Non-operating altitude	0 - 4877 m
Storage temperature (T-T)	-40 - 70 °C
Operating temperature (T-T)	0 - 45 °C
Storage relative humidity (H-H)	0 - 95 %
Operating relative humidity (H-H)	10 - 85 %
Supported network protocols	IPv6

Weight and Dimensions

Depth	310 mm
Width	437 mm
Height	44 mm
Weight	4900 g