EasyManuals Logo

Juniper EX3300 Hardware Guide

Juniper EX3300
354 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #125 background imageLoading...
Page #125 background image
periodic on page 215
preferred on page 216
primary (Address on Interface) on page 217
proxy-arp on page 218
rpf-check on page 219
speed (Ethernet) on page 220
traceoptions (Individual Interfaces) on page 221
traceoptions (Interface Process) on page 223
transmit-interval (Liveness Detection) on page 224
traps on page 225
unit on page 226
vlan (802.1Q Tagging) on page 227
vlan-id (VLAN Tagging and Layer 3 Subinterfaces) on page 228
vlan-tagging on page 229
[edit chassis] Configuration Statement Hierarchy on EX Series Switches
This topic lists supported and unsupported configuration statements in the [edit chassis]
hierarchy level on EX Series switches.
Supported statements are those that you can use to configure some aspect of a
software feature on the switch.
Unsupported statements are those that appear in the command-line interface (CLI)
on the switch, but that have no effect on switch operation if you configure them
Not all features are supported on all switch platforms. For detailed information about
feature support on specific EX Series switch platforms, see EX Series Switch Software
Features Overview.
This topic lists:
Supported Statements in the [edit chassis] Hierarchy Level on page 105
Supported Statements in the [edit chassis] Hierarchy Level
The following hierarchy shows the [edit chassis] configuration statements supported on
EX Series switches:
chassis {
aggregated-devices {
ethernet {
device-count number;
lacp {
link-protection non-revertive;
system-priority system-priority-number
}
}
}
105Copyright © 2015, Juniper Networks, Inc.
Chapter 3: Configuration Statements

Table of Contents

Other manuals for Juniper EX3300

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Juniper EX3300 and is the answer not in the manual?

Juniper EX3300 Specifications

General IconGeneral
Ethernet LANYes
Authentication methodRADIUS, TACACS+
Connectivity technologyWired
Ethernet interface typeGigabit Ethernet
Number of VLANs4096
Networking standardsIEEE 802.1ab, IEEE 802.1D, IEEE 802.1Q, IEEE 802.1s, IEEE 802.1w, IEEE 802.1x, IEEE 802.3, IEEE 802.3ab, IEEE 802.3ad, IEEE 802.3x, IEEE 802.3z
Ethernet LAN data rates10, 100, 1000 Mbit/s
Copper ethernet cabling technology1000BASE-T, 100BASE-TX, 10BASE-T
Console port-
ExpressCard slotNo
Fiber ports quantity4
USB 2.0 ports quantity0
Basic switching RJ-45 Ethernet ports quantity48
Throughput130 Mpps
Number of queues8
MAC address table16000 entries
Maximum data transfer rate176 Gbit/s
Supported data transfer rates10, 100, 1000Mbps
Switch typeManaged
Switch layerL2
Security algorithmsSSH-2
Power sourceAC
AC input voltage100 - 240 V
Power consumption (typical)100 W
Form factor1U
Product colorBlack
Flash memory1024 MB
Processor frequency1000 MHz
Compatible operating systemsJunos
Operating altitude0 - 3049 m
Non-operating altitude0 - 4877 m
Storage temperature (T-T)-40 - 70 °C
Operating temperature (T-T)0 - 45 °C
Storage relative humidity (H-H)0 - 95 %
Operating relative humidity (H-H)10 - 85 %
Supported network protocolsIPv6
Weight and Dimensions IconWeight and Dimensions
Depth310 mm
Width437 mm
Height44 mm
Weight4900 g

Related product manuals