Juniper EX3300 Hardware Guide

native-vlan-id
Syntax native-vlan-id number;
Hierarchy Level [edit interfaces ge-fpc/pic/port],
[edit interfaces interface-name]
Release Information Statement introduced in Junos OS Release 8.3.
Statement introduced in Junos OS Release 12.2 for ACX Series Universal Access Routers.
Statement introduced in Junos OS Release 12.3R2 for EX Series switches.
Statement introduced in Junos OS Release 13.2X51-D20 for the QFX Series.
Description Configure mixed tagging support for untagged packets on a port for the following:
• M Series routers with Gigabit Ethernet IQ PICs with SFP and Gigabit Ethernet IQ2 PICs
with SFP configured for 802.1Q flexible VLAN tagging
• MX Series routers with Gigabit Ethernet DPCs and MICs, Tri-Rate Ethernet DPCs and
MICs, and 10-Gigabit Ethernet DPCs and MICs and MPCs configured for 802.1Q flexible
VLAN tagging
• T4000 routers with 100-Gigabit Ethernet Type 5 PIC with CFP
• EX Series switches with Gigabit Ethernet, 10-Gigabit Ethernet, 40-Gigabit Ethernet,
and aggregated Ethernet interfaces
When the native-vlan-id statement is included with the flexible-vlan-tagging statement,
untagged packets are accepted on the same mixed VLAN-tagged port.
The logical interface on which untagged packets are received must be configured with
the same VLAN ID as the native VLAN ID configured on the physical interface. To configure
the logical interface, include the vlan-id statement (matching the native-vlan-id statement
on the physical interface) at the [edit interfaces interface-name unit logical-unit-number]
hierarchy level.
When the native-vlan-id statement is included with the interface-mode statement,
untagged packets are accepted and forwarded within the bridge domain or VLAN that
is configured with the matching VLAN ID.
Options number—VLAN ID number.
Range: (ACX Series routers and EX Series switches) 0 through 4094.
Required Privilege
Level
interface—To view this statement in the configuration.
interface-control—To add this statement to the configuration.
Related
Documentation
Configuring Mixed Tagging Support for Untagged Packets•
• Configuring a Logical Interface for Access Mode
• Configuring the Native VLAN Identifier (CLI Procedure)
• Understanding Bridging and VLANs on EX Series Switches
213Copyright © 2015, Juniper Networks, Inc.
Chapter 3: Configuration Statements

Juniper EX3300 Specifications

General

Ethernet LAN	Yes
Authentication method	RADIUS, TACACS+
Connectivity technology	Wired
Ethernet interface type	Gigabit Ethernet
Number of VLANs	4096
Networking standards	IEEE 802.1ab, IEEE 802.1D, IEEE 802.1Q, IEEE 802.1s, IEEE 802.1w, IEEE 802.1x, IEEE 802.3, IEEE 802.3ab, IEEE 802.3ad, IEEE 802.3x, IEEE 802.3z
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Copper ethernet cabling technology	1000BASE-T, 100BASE-TX, 10BASE-T
Console port	-
ExpressCard slot	No
Fiber ports quantity	4
USB 2.0 ports quantity	0
Basic switching RJ-45 Ethernet ports quantity	48
Throughput	130 Mpps
Number of queues	8
MAC address table	16000 entries
Maximum data transfer rate	176 Gbit/s
Supported data transfer rates	10, 100, 1000Mbps
Switch type	Managed
Switch layer	L2
Security algorithms	SSH-2
Power source	AC
AC input voltage	100 - 240 V
Power consumption (typical)	100 W
Form factor	1U
Product color	Black
Flash memory	1024 MB
Processor frequency	1000 MHz
Compatible operating systems	Junos
Operating altitude	0 - 3049 m
Non-operating altitude	0 - 4877 m
Storage temperature (T-T)	-40 - 70 °C
Operating temperature (T-T)	0 - 45 °C
Storage relative humidity (H-H)	0 - 95 %
Operating relative humidity (H-H)	10 - 85 %
Supported network protocols	IPv6

Weight and Dimensions

Depth	310 mm
Width	437 mm
Height	44 mm
Weight	4900 g