EasyManuals Logo

Juniper EX3300 Hardware Guide

Juniper EX3300
354 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #88 background imageLoading...
Page #88 background image
Regex or wildcards are not supported for interface-type prefixes. For example, prefixes
ge, fe, and xe must be mentioned explicitly.
An interface-range definition can contain both member and member-range statements
within it. There is no maximum limit on the number of member or member-range
statements within an interface-range. However, at least one member or member-range
statement must exist within an interface-range definition.
Example: Interface
Range Common
Configuration
Configuration common to an interface range can be added as a part of the interface-range
definition, as follows:
[edit]
interfaces {
+ interface-range foo {
+ member-range ge-1/0/0 to ge-4/0/40;
+ member ge-0/1/1;
+ member ge-5/[1-10]/*;
/*Common configuration is added as part of interface-range definition*/
mtu 256;
hold-time up 10;
ether-options {
flow-control;
speed {
100m;
}
802.3ad primary;
}
}
}
An interface-range definition having just member or member-range statements and no
common configurations statements is valid.
These defined interface ranges can be used in other configuration hierarchies, in places
where an interface node exists.
Example:
Interface-Range foo
protocols {
dot1x {
authenticator {
Used Under the
Protocols Hierarchy
interface foo{
retries 1;
}
}
}
}
foo should be an interface-range defined at the [interfaces] hierarchy level. In the above
example, the interface node can accept both individual interfaces and interface ranges.
TIP: To view an interface range in expanded configuration, use the (show |
display inheritance) command. For more information, see the CLI User Guide.
Copyright © 2015, Juniper Networks, Inc.68
Network Interfaces for EX4300 Switches

Table of Contents

Other manuals for Juniper EX3300

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Juniper EX3300 and is the answer not in the manual?

Juniper EX3300 Specifications

General IconGeneral
Ethernet LANYes
Authentication methodRADIUS, TACACS+
Connectivity technologyWired
Ethernet interface typeGigabit Ethernet
Number of VLANs4096
Networking standardsIEEE 802.1ab, IEEE 802.1D, IEEE 802.1Q, IEEE 802.1s, IEEE 802.1w, IEEE 802.1x, IEEE 802.3, IEEE 802.3ab, IEEE 802.3ad, IEEE 802.3x, IEEE 802.3z
Ethernet LAN data rates10, 100, 1000 Mbit/s
Copper ethernet cabling technology1000BASE-T, 100BASE-TX, 10BASE-T
Console port-
ExpressCard slotNo
Fiber ports quantity4
USB 2.0 ports quantity0
Basic switching RJ-45 Ethernet ports quantity48
Throughput130 Mpps
Number of queues8
MAC address table16000 entries
Maximum data transfer rate176 Gbit/s
Supported data transfer rates10, 100, 1000Mbps
Switch typeManaged
Switch layerL2
Security algorithmsSSH-2
Power sourceAC
AC input voltage100 - 240 V
Power consumption (typical)100 W
Form factor1U
Product colorBlack
Flash memory1024 MB
Processor frequency1000 MHz
Compatible operating systemsJunos
Operating altitude0 - 3049 m
Non-operating altitude0 - 4877 m
Storage temperature (T-T)-40 - 70 °C
Operating temperature (T-T)0 - 45 °C
Storage relative humidity (H-H)0 - 95 %
Operating relative humidity (H-H)10 - 85 %
Supported network protocolsIPv6
Weight and Dimensions IconWeight and Dimensions
Depth310 mm
Width437 mm
Height44 mm
Weight4900 g

Related product manuals