Kenwood eXcelon KDC-X991 User Manual

English
|
13
4 Exit Sound Management mode
Press the [FNC] button.
Position Control
1 Enter Position mode
Using the Control knob, select "DSP" > "SND
CONT" > "POSITION".
For the operation method, refer to <Function
Control mode> (page 11).
2 Select the Position item to adjust
Turn the Control knob or push it towards left
or right.
Icon Position Item
"PRESET" Preset Position
"MANUAL" Manual Position
3 Enter the Position item
Press the Control knob.
4 Adjust the Position item
Preset Position Setting
Push the Control knob towards right or left.
Each time you push the knob, the setting alternates
between the settings shown in the table below.
Range
All/ Front-Left/ Front-Right/ Front
Manual Position Setting
1 Select the items to adjust for Position.
Push the Control knob towards up or down.
Display Position Item
"L" "FRONT"
Front Left
"L" "REAR"
Rear Left
"L" "SW"
Subwoofer Left
"FRONT" "R"
Front Right
"REAR" "R"
Rear Right
"SW" "R"
Subwoofer Right
2 Adjust the Position.
Turn the Control knob or push it towards left
or right.
Each time you push the knob, the setting
alternates between the settings shown in the
table below.
Range
0.00 — 3.33 (feet)
5 Exit Position mode
Press the [FNC] button.
⁄
• About the position setting
First, set the using environment with “DTA” in <Sound
Management system> (page 12).
Preset position setting is for selecting the actual listening
position.
Manual position setting is for further adjustment of the
position selected in preset position setting. This setting
value can be memorized for each preset position.
• When using the Subwoofer Left and Subwoofer Right as
a single sub woofer, set the left side and right side to the
same value.
• Preset Position initial settings
Preset Position Front Rear Subwoofer
Left Right Left Right Left Right
ALL 000000
Front-Left 0 1.17 0 1.17 0 0
Front-Right 1.17 0 1.17 0 0 0
Front 0 0 3.33 3.33 0 0
B64-3767-0000KEnglish.indd13B64-3767-0000KEnglish.indd13 07.5.102:15:44PM07.5.102:15:44PM

Kenwood eXcelon KDC-X991 Specifications

FM Tuner Section

frequency range	87.9 MHz – 107.9 MHz
usable sensitivity	9.3 dBf (0.8 μV/75 Ω)
quieting sensitivity	15.2 dBf (1.6 μV/75 Ω)
frequency response	30 Hz – 15 kHz
signal to noise ratio (MONO)	70 dB
selectivity	≥ 80 dB
stereo separation	40 dB

AM Tuner Section

frequency range	530 kHz – 1700 kHz
usable sensitivity	28 dBμ (25 μV)

CD Player Section

spindle speed	1000 – 400 rpm (CLV 2times)
frequency response	10 Hz – 20 kHz
total harmonic distortion	0.008 %
signal to noise ratio	110 dB
dynamic range	93 dB

USB Interface

usb standard	USB 1.1/ 2.0
maximum supply current	500 mA
file system	FAT16/ 32

Audio Section

maximum output power	50 W x 4
full bandwidth power	22 W x 4
speaker impedance	4 – 8 Ω
tone action band 1	60 – 200 Hz ±9 dB
tone action band 2	250 – 1k Hz ±9 dB
tone action band 3	1.25k – 4k Hz ±9 dB
tone action band 4	5k – 16k Hz ±9 dB
preout level / load	5000 mV/10 kΩ
preout impedance	≤ 80 Ω

Auxiliary Input

frequency response	20 Hz – 20 kHz
input maximum voltage	1200 mV
input impedance	100 kΩ

General

operating voltage	14.4 V
current consumption	10 A
installation size	182 x 53 x 155 mm
weight	3.31 lbs (1.5 kg)