Kenwood eXcelon KDC-X991 User Manual

36
|
English
⁄
• Resume is canceled if "CANCEL" or "NO" is selected.
- "CANCEL": Press the Control knob.
- "NO": Select "NO" using the Control knob. Press the
Control knob.
• The resume function may be disabled depending the
condition of the vehicle or battery. The audio file may be
lost if the resume function is disabled.
Record or copy while the engine is running.
When music CD is inserted
Setting the recordable time
Set the recordable time for recording music CD.
1 Enter Mode setting
Using the Control knob, select "IMPORT CD" >
"MODE SET".
For the operation method, refer to <Function
Control mode> (page 11).
2 Set the recordable time
Turn the Control knob.
Display Setting Max. recording time*
"Standard" Standard recording Approx. 8 hours
"Long Play"
…
Approx. 12 hours
"Super Long Play" Extended time recording Approx. 16 hours
3 Exit Mode setting
Press the Control knob.
⁄
• * The maximum recordable time is obtained when there
is no other file. The actual recording time depends on
the song.
• The sound quality for Extended recording is lower than
for Standard recording.
Recording music CD
Music CD can be compressed and stored in internal
memory.
( ; Int Mem)CD
;CD001
vCD001_010
vCD000_001
vCD001_003
v
v
v
v.
⁄
• Read <About Internal Memory> (page 35) before
starting copy.
• Music CD can be recorded only from the internal CD.
Recording is performed at x1 speed.
1 Insert a CD-DA
Insert the music CD to record.
Refer to <Playing CD & Audio file> (page 30).
2 Change to import mode
Using the Control knob, select "IMPORT CD" >
"IMPORT".
For the operation method, refer to <Function
Control mode> (page 11).
3 Select record mode
Push the Control knob towards right or left.
Multiple song record mode is set when the control
knob is turned right and single song record mode
is set when it is turned left.
4 Select the song to record
Turn the Control knob or push it towards up or
down.
Record mode Operation
Single song Selects a single song.
Multi song Selects all songs or from specified song to
the last song.
5 Confirm the song
Press the Control knob.
6 Name the target file or folder
Using the Control knob, select "NAME SET ".
Recording starts if "SKIP" is selected.
7 Enter Name set mode
Press the Control knob.
B64-3767-0000KEnglish.indd36B64-3767-0000KEnglish.indd36 07.5.102:15:57PM07.5.102:15:57PM

Kenwood eXcelon KDC-X991 Specifications

FM Tuner Section

frequency range	87.9 MHz – 107.9 MHz
usable sensitivity	9.3 dBf (0.8 μV/75 Ω)
quieting sensitivity	15.2 dBf (1.6 μV/75 Ω)
frequency response	30 Hz – 15 kHz
signal to noise ratio (MONO)	70 dB
selectivity	≥ 80 dB
stereo separation	40 dB

AM Tuner Section

frequency range	530 kHz – 1700 kHz
usable sensitivity	28 dBμ (25 μV)

CD Player Section

spindle speed	1000 – 400 rpm (CLV 2times)
frequency response	10 Hz – 20 kHz
total harmonic distortion	0.008 %
signal to noise ratio	110 dB
dynamic range	93 dB

USB Interface

usb standard	USB 1.1/ 2.0
maximum supply current	500 mA
file system	FAT16/ 32

Audio Section

maximum output power	50 W x 4
full bandwidth power	22 W x 4
speaker impedance	4 – 8 Ω
tone action band 1	60 – 200 Hz ±9 dB
tone action band 2	250 – 1k Hz ±9 dB
tone action band 3	1.25k – 4k Hz ±9 dB
tone action band 4	5k – 16k Hz ±9 dB
preout level / load	5000 mV/10 kΩ
preout impedance	≤ 80 Ω

Auxiliary Input

frequency response	20 Hz – 20 kHz
input maximum voltage	1200 mV
input impedance	100 kΩ

General

operating voltage	14.4 V
current consumption	10 A
installation size	182 x 53 x 155 mm
weight	3.31 lbs (1.5 kg)